20 Most Recent Canon PIXMA MP150 All-In-One InkJet Printer - Page 9 Questions & Answers

Verify the ink cartridge.

error number 5200

paper jam clean the paper out of it turn it off and back on should fix it

you have not provided enough details but i think you paper conveyance path may be obstructed, could be torn pieces of paper from previous jam. otherwise supply more info.

Replacing the absorber is a hard task. if this is the first time you have had this problem.Hold the ON/OFF button down, while holding the Stop/Reset botton down. Look under your finger untill the green LED is on. Then follow these - press reset button twice, wait a few seconds, and then press it 4 times. (You hold the power button down the whole time.) Then let go of both buttons. Then turn off the printer, it takes a while to respond to this. Turn it back on and off you go!!

Ink Absorber Full This may clear the ink absorber problem. There is ink absorbers located at both ends of the printer where the ink head move. To dry the ink absorber, power up the printer and open the cover so the ink cartridges and print head will move to the middle of the printer. Then take several sheets of absorbent tissue, fold it into a pad and place it inside the printer over the ink absorber on the far left hand side of the printer to soak up the excess ink. You may need to change the absorbent tissue a few times. Then repeat the same procedure on the right hand ink absorber. Close the lid and the printer should now function normally.

1. plug off power cable
2. press and hold stop/reset button
3. plug on power cable
4. press and hold power button(still hold stop/reset buttn)
5. still hod power button, loose stop/reset button
6. press stop/reset 2X then loose power button, wait until 0 displayed
7. press stop/reset 1X
8. press power button 1X, printer will print 1 time
9. press stop/reset 2X
10. press power button 1X,printer will print 1 time
11. press stop/reset button 3X
12. press power button 1X ( no print proses)
13. press stop/reset 4X
14. press power button longer than before for turn off printer, if print not turn off plug off power cable
15. turn on printer and error 27 will disappear

i hope this helpfull
thanks for using fixya

First you need driver..you can download from manufacturer website..After that you can install it...

Please send it to your nearest service centre.

This seems to be fault in the transport of the paper in the rollers. So if you have used any adhesive sticker printing, it is possible that some glue has got clogged into the rollers. If not there can be some jammed paper in the rollers or the mechanism. So start this work only if you are mechanically able with the right tools. Remove the covers to get access to the mechanism . Remove the motor drive assembly , the fitting of the motor to the mechanism. Once this is removed the rollers can be turned manually so that you will be able to feed a paper to see the progress of the movement while studying if there is any obstruction or damage to the paper. There is a in-detect sensor, usually an opto-coupler , make sure this is not clogged or dirty as this IR detection feeds the signal to the processor for starting the motor drive feed. Reassemble but make sure the rollers are aligned to be in equal gap to feed the paper without a side pull. Now you must print and see if the fault has changed. If not repeat the above work to confirm the area of obstruction.

Check this link for tips; http://www.ehow.com/how_113761_clear-printer-paper.html

Hi,
You will need to download the software MP Navigator in order to scan successfully.
You can get this and associated drivers here.
http://software.canon-europe.com/products/0010639.asp
Be sure to shortlist the software by selecting the desired OS and Language.

I just bought a CANON PIXMA MP145. I installed the drivers perfectly but now when i try to scan something, it gives me an error code 2114,0...plz solve this problem

i had to get mine directly from canon for my pixma mp620 http://www.usa.canon.com/consumer/controller?act=DownloadIndexAct

try this link, you can reset the ink counter without software: http://www.fixya.com/support/r7066832-reset_canon_pixma_mp140

press stop reset button for few seconds and you can use your black cartridge for printing,but do remember to put use black only setting in ur printer cartridge settings.

E22 mean
Carriage error