Top 20
Frigidaire ATF6000ES Front Load Washer Questions & Answers
I have a Frigidaire Affinity
"pause" isn't something you can reset exactly I'm afraid. Pause means that the washer door was opened mid cycle so all you should need to do is shut the door to restart the cycle. Unfortunately if it doesn't re-start, it means that your door latch assembly has failed and isn't sensing that the door is shut. You'll need to order and replace the door latch assembly to fix the issue.
It's actually a fairly easy part to replace if you're handy. You'll need to unplug the washer and open the door to start with. Then there is a wire ring around the front lip of the rubber door gasket. Use a flat head screwdriver/needle nose pliers and pry the wire ring off. From there you can pull the gasket back out of the way. Remove the screws going into the door latch from the front and reach behind to replace the door latch assembly.
Make SURE the door strike on the door isn't broken too.
that's only a 6$ or so item.
Here's a site for parts and a video on how to replace it.
https://www.repairclinic.com/PartDetail/Door-Switch/131763256/4547033?modelNumber=ATF6000FS1
Hope this helps you.
2/17/2018 1:00:04 PM •
Frigidaire...
•
256 views • 0 helpful votes
Will not complete the final
there seems to be a problem in the water pump as its not draining properly check that there's not a button or other debris in the system first eric
12/29/2017 2:54:03 PM •
Frigidaire...
•
219 views • 0 helpful votes
My frigidaire front load washer stopped working
It sounds like the pump has stopped and may have sucked a sock or rag into it. May need to pull the washer out, remove the back. Unplug the washer and see if you can manually turn the pump/motor belt. It could also be the motor but I would check to see if they turn. If not, remove the belt and manually try to turn each and see if they turn.
11/6/2017 9:36:03 PM •
Frigidaire...
•
182 views • 0 helpful votes
I have a Frigidaire front
the most common cause is worn out brushes in the motor, sme brands you can rplace the brushes others require a new complete motor
9/27/2017 7:03:03 PM •
Frigidaire...
•
104 views • 0 helpful votes
How to unclog drain hose/pump? my front loader
First of start by checking the rubber gasket seals around the door and making sure those are good and clean and dry. Then inspect the barrel itself. My daughter loves to leave scraps of paper in her pockets that then get stuck in my front loader. Clear any debris from the barrel. Does your machine have a small front access panel or back access to get to the filter? Most front loaders have some sort of filter on them apart from the barrel. If you can find this part, it is a common culprit. Mine is a tube shaped basket with a front access panel on this one. On the front loader before this one is was back panel accessable under the drum. when you check these have a bucket and some thing mop up with handy, towels, mop, etc. One other thing to consider is the drain hose from the machine. I have flushed mine using a garden hose in the yard and used a little bleach.
5/12/2017 12:09:03 PM •
Frigidaire...
•
1,335 views • 0 helpful votes
E20 error message
replace the control panel or have it repaired,there is no e20 listed as a trouble code,so it needs to be replaced.
To clear latest stored error code:
Place the control into Diagnostic test Mode.
- Turn the program knob clockwise 9 clicks from the Start Position. The control will signal the last error code.
- Press and hold the Options and Pause Cancel buttons for 3 seconds. The code will be cleared.
- Exit Diagnostic Mode to return the washer to normal operation.
Error code - Fault condition
E11 Fill time too long.
E13 Water leak in tub or air leak in air bell.
E14 Reed switch.
E21 Water not pumping out fast enough.
E23 Drain pump relay on control board failed.
E24 Drain pump relay on control board failed.
E31 Better models. Pressure sensor not communicating with control board.
E35 Better models. Pressure sensor indicates water overfill.
E41 Control board thinks the door switch is open.
E42 Door remains locked after cycle is completed.
E43 Control board problem.
E44 Control board problem.
E45 Control board problem.
E46 Control board problem.
E47 Board thinks the door PTC circuit is open in spin.
E48 Board thinks the door PTC circuit is closed.
E52 Bad signal from tacho generator.
E55 Motor overheating.
E56 High motor current.
E57 High current on inverter.
E58 High current on motor phase.
E59 No tacho signal for 3 seconds.
E5A High temperature on heat sink.
E5B High temperature on heat sink.
E5C High temperature on heat sink.
E5D Communication problem.
E5E Communication problem.
E5F Communication problem.
E67 Input voltage on microprocessor incorrect.
E75 Better models only. Water temperature sensor circuit.
E76 Better model only. NTC temperature for the cold water valve over the limits.
E95 Communication error.
EB1 Incoming power frequency out of limits.
EB2 Incoming line voltage above 130 VAC.
EB3 Incoming line voltage below 90 VAC.
EF1 Clogged drain pump.
EF2 Too much soap.
4/22/2017 1:36:02 PM •
Frigidaire...
•
243 views • 0 helpful votes
Our front load washer had
The washtub suspension allows it to move but when overloaded it will move rather more than it is designed for and could open a gap between the washtub and the door large enough to allow items to slip through.
The suspension is carefully designed to absorb the out of balance forces, with which the washer would be noisy and tend to "walk" around the kitchen. These days consumers demand smoother and quieter performance from their washers and so it is increasingly important not to overload them.
A friend called out the service engineer to his new washer that he had been operating just like his old one. The engineer began by plugging in a laptop and looking accusingly at him said he had overloaded his new machine nine times in the few weeks since it was delivered. Guessing is no longer an acceptable method of loading the washing machine...
3/23/2017 1:33:02 AM •
Frigidaire...
•
123 views • 0 helpful votes
How do i unlock the wash settings?
Hello Salvatore, thank you for your post!
Based off what you have described you need to know how to unlock your Frigidaire washer, ATF6000ES. If the control panel is locked you would need to hold down the options and select buttons for ten seconds. "LOC" should no longer be displayed on the control and the washer should continue operations. I hope this information is helpful to you. -Matt
4/21/2016 1:20:17 AM •
Frigidaire...
•
298 views • 1 helpful votes
Large dark brown spots appearing after washing
Normally a washer does not cause a staining problem, but If something inside the washer has rusted, it could. I would check your water tank. Drain water from the drain cock at the bottom of the tank, and see how dirty it is. If it is dirty, you need to drain the water until it is almost clear.
8/13/2015 9:19:37 PM •
Frigidaire...
•
570 views • 0 helpful votes
Won't stay on wash cycle I select
I appreciate your post, Sandy!
I understand that your Frigidaire washer, ATF6000ES, will not stay on the wash cycle you select. This could be a faulty control panel, wiring harness, or keypad. Have you reset your washer? You can perform a reset by disconnecting the power from your washer for at least ten minutes. If the reset does not help to correct your issue I would recommend seeking a professional technician for proper diagnosis and repair. This will help you avoid any unnecessary part purchases. -Matt
8/7/2015 9:58:25 PM •
Frigidaire...
•
140 views • 0 helpful votes
Why won't Affinity fill or spin?
Probably there is water in the drum or the pressure switch is jam in a state of "full of water" or washing machine didn't drain water .. So, the fault should be sought in the elements responsible for control the level (pressure switch, pcb...etc.) or control draining water (drain pump, pcb, filter....etc.).
The precondition that the machine goes into a spin cycle is that pressure switch folded down to position "empty of water".
Dado
7/24/2015 6:17:37 PM •
Frigidaire...
•
161 views • 0 helpful votes
Why do I get dark rust spots on clothes
COULD BE THE FINISH CAME OFF THE DRUM AND IS RUSTED,LOOK AND SEE IF YOU CAN FIND IT,IF YOU DO,GET A GREEN PAD AND SCRUB IT AND TOUCH UP WITH APPLIANCE PAINT.
8/13/2015 9:27:54 PM •
Frigidaire...
•
64 views • 0 helpful votes
Not finding what you are looking for?