20 Most Recent
Fisher and Paykel GWL11 Top Load Washer - Page 4 Questions & Answers
Wont spin
you have to check all the harness connections on this machine and when you realize that this is going to happen often you may want to consider tossing this in a dumpster.
Replaced water pump and control panel, have power, but just beeps.
ths.gardenweb.com > Home Forums > Laundry Room
Mar 5, 2008 - My GWL11 Top loading washer has had nothing but problems! ... 4) (Rinse Phase) Drain the water, then lock the lid for spin. ..... I plug the power cord in and I have nothing on the control panel. ..... As the controller was only replaced early in January, I've flicked F&P NZ an email to see if it's still under ...
www.instructables.com/.../How-to-repair-a-
Fisher-
Paykel-
W...
InstructablesI removed the pump and control panel, found no blockage in the pump, so far ... Ihave just tried to fill my F/P machine but the water is just dripping in. ... I have aFisher Paykel washer have replaced the control module and now it .... washing machine MW612, stopped working and displayed beeping sound every second.
Why does it leak, even when machine is not running?
ths.gardenweb.com > Home Forums > Laundry Room
May 6, 2008 - Got a small drip/leak with my GWL11 washer..... The washer is ...Small leak/drip with Fisher & Paykel GWL11 Washer (with pictures) ..... New project for a new year: Light a fire under plans for an outdoor oven and claim the best pizza in town ... Speed Queen Front Load AFN50 Washer Review - Long Post.
ths.gardenweb.com > Home Forums > Laundry Room
Mar 5, 2008 - My GWL11 Top loading washer has had nothing but problems! ... I have a Fisher Paykel GWL11 that I purchased new and have loved until this problem started. ... The machine fills with a small amount of water to saturate the clothes ...... Fault 36 is related to water leaking, but is *not* the kind of leaking from ...
www.faqqq.com/.../
fisher-
paykel-
gwl11-
washer-
leaking-and-squealing-
fish...
Question Product: Fisher and Paykel GWL11 Top Load Washer Question Details:Fisher Paykel ... Small leak/drip with Fisher & Paykel GWL11 Washer (with .
12/12/2015 12:46:04 AM •
Fisher and...
•
Answered
on Dec 12, 2015
Fisher & paykel (mw511)
check out the DRAIN MOTOR PUMP , its a small motor with 2 hoses connected to it , it could be clogged , need to remove it , inspect inside the impellers for any debri , clean it , re install and try again , hope this helpful AJ
My f&p top loader mw511 continously beeps and
Hi just read your posting.Now when the machine starts beeping a series of lights will light up.These lights will be in a row of 8 lights.Starting from the left to right which lights are lit when the machine is beeping,Is it the 2nd and 4th or the 1st and 7th ---etc---?Please reply with additional information and I am sure I can help you.Looking forward to your reply.
Fischer & Paykel washer will not drain. What
take clothes out,check the hose for is it blocked or kinked put a clothes hanger in hose and see if you can un-snake any thing out,then put draino-max jel in washer and let it set for about 2-3hrs,see there may be hair blocking the pump were it drains,this stuff work great for front-loader so let it sit.then try putting on drain it may take a few times,the when it drains,run washer on full cycle no clothes hot-water let it go through a full wash cycle etc.
My washing machine wont spin or empty, is it repairable?
Your pump and drain pipe could be blocked.
Check for squashed drain pipe.
Switch off power and water taps
Bail out all water you can with cup
move machine out from wall
tilt machine back on a wall to look under to find pump.
push white pump retainer clip outwards
and turn pump anticlockwise to remove.
and check for item in the impeller.
Cold water valve not working. have checked that water is at outlet of cold water tap. Can you help? thank you
Water Valve Test
When in Diagnostic Mode, the WASH TEMP UP button turns the hot water valve on. The Hot LED is on when the hot valve is on. The WASH TEMP DOWN button turns the cold water valve on. The Cold LED is on when the cold valve is on.
DIAGNOSTIC MODE
Turn the power on at the power point but off at the machine. Press and hold the WASH TEMP DOWN button and then the POWER button until the machine gives 2 short beeps and lights up. Release buttons when the beeps indicate diagnostic mode has been entered.
There maybe up to 3 filters cold water line. There is sometimes 1 at each end of the water hose itself and also in the valve which can be removed with pliers. (see picture)
Undo the 2 screws at the back of the buttons panel
Undo the connection of the valve
If you are good with a multimeter check that there is about 65 ohms resistance across the terminals of the valve. If not, then replace the valve.
Also sometimes the workings inside the valve can jam shut so replace the valve.
Not finding what you are looking for?