20 Most Recent
Hotpoint Ultima WF860 Front Load Washer - Page 8 Questions & Answers
Saying test on the display unit
There are few methods, depends on the age of the appliance.
Press the Start/Cancel button until all the console LED's illuminate. Press both Start/Cancel and On/Off buttons together until d OFF appears. The default screen returns and you can select a new programme.
Simply press the Cancel button and the appliance returns to default. Press On/Off and Start/Cancel toghether with top left option button until d OF appears.
or
Switch off at mains, press and hold On/Off & Start/Cancel buttons, switch mains back on, keep holding down buttons until Doff appears in display.
I have a hotpoint ultima
Hi,
F10 is a pressure switch not sensing error. Basically its a filling problem.
What you need to do is make sure the fill hose isn't kinked up at the back stopping it from filling fast enough.
If
the hose is OK then take off the fill hose and aim it into a bucket and
turn the water tap on. Then from there see what the water pressure is
like there.
If its weak then you need the water pressure sorting out.
If the pressure is fine then you will need a multimeter and test the water valves on top and see if any of them are faulty.
But the F10 error code is a filling issue.
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
Lcd
What is the model number list on the door jamb?
How do I stop my washing machine door alarm
go to instru.manual section troubleshooting and fix it. God bless youif doesnot have it download from
www.fitness.manualsonline.comHowever try this.The processes below will get most controls unlocked.
Duet Washer - Press and hold the END OF CYCLE SIGNAL button for 15 seconds.
Whirlpool Duet Dryer - Press and hold the END OF CYCLE SIGNAL button for 15 seconds.
Kenmore Elite Washer - Press and hold the DRAIN/SPIN button for 15 seconds.
Some Models- Press and hold the control lock button for 15 seconds.
If none of these work try unplugging for 5 minutes
UNBLOCK FILTER ON WF860P WASHING MACHINE
has it got a filter if so should be around the kick plate under the door if there is no door some hotpoints have a 1 just indide the door at the top if still no you havent got one
Hotpoint ultima Wt920 problem F5
Do the following.
- Switch off the machine, unplug or disconnect the mains power to the machine and turn off the water supply to the machine.
- Remove the filter and make sure that the filter
is not blocked and is clean and clear of all debris. Clean as required.
Note that if the machine has stopped and not fully drained then you may
be able to drain out the excess water by removing or disconnecting the
waste hose and laying it on the ground in a tray. It may take a few
minutes to empty but it will save a small flood. Alternatively bale out
the sump under the main screen filter plate.
- Proceed by checking the drain hose for proper connection and kinks and make sure that it is not blocked or restricted.
- Also check that the main waste drain pipe and one
way valve to a sink waste connection if you use one, is not blocked and
clean if required.
- Access the pump from under the lower rotor arm
and protective grille and check that the impeller is free to move and is
not clogged or restricted by debris or sludge. Clean as required.
- Reconnect the power and switch the machine on.
If the problem persists then do the following.
7. Switch off the
machine and disconnect the mains power. It is a good idea to take
digital pictures of the pump assembly before attempting to work on it or
remove it so that you can refer back to it when you reassemble the unit
or replace it with a new unit at a later date / time.
8. Remove and check the electrical connections to the pump and make sure they are in good order.
9. Remove the
connecting hoses, and expect water to drain out and make sure the pipes
are not blocked with debris or any object blockage. If they are then
clean them thoroughly.
10. Then remove the pump
and check motor is OK and that the motor turns OK. Also check that the
pump impeller vanes are in good order and not blocked. If necessary
replace the pump with a new and identical unit.
11. Carefully reassemble
the pump observing the correct placement of gaskets, seals, O Rings,
hoses and securing straps, electrical wiring.
12. Reconnect the hoses and then reconnect power and switch the machine on.
Hotpoint F-01 Error code
Hi
my washing machine is 2 years old, hotpoint wt761p showinf f-01. it hasnt finished it cycle. turned off by mains to open the door and get washing out.
please help!!
stella
Not finding what you are looking for?