Top 20 Ryobi Lithium Ion 18 Volt 18v Cordless String Trimmer Edger Weedwacker P2002 Questions & Answers

have you read your operators manual.? They generally just unclip and pull out.

On the WEB, maybe they can help:

Cordless String Trimmer Edger‎

Adwww.worx.com/‎

it might be that your battery need changing even though the machine is lightly used the battery might have aged prematurely.

Once you remove the spool cap and the spool, you cannot remove the head from the motor. It is not a replacement part. Ryobi P2002 Cordless String Trimmer Parts

full throttle, tap on ground, line should feed automaticaly.

Check to make sure you don't have a staple stuck under the hammer. If the spring feed is working, then something is keeping the staples from sliding under the hammer. Can you hear the hammer hitting? Does it leave an impression on the wood?

Make a sharp bend in the line and insert it into the hole in the spool hub. Start wrapping the replacement line in the direction shown on the spool.

When looking at the head, you will see to two gray rectangle pieces. Press them both at the same time between your thumb and forefinger and then pull. It should come unlatched and reveal the line spool on the inside

Ryobi Trimmers unscrew halfway down the shaft (so it fits in the box). If this gets loose, the trimmer will stop working. Simply tighten the connection between the upper and lower half.

the wiring maybe disconnected, either at the switch or down near the head of the trimmer

Question edited for clarity and toss in some CAPS. None Larry! It is a 2 stroke machine so the crankcase is lubricated by the oil that is mixed with the gas. I double checked to see if it had a gearbox. It is just an engine and a fan https://www.google.com/search?q=ryobi+ry09056+crankcase+oil Manual which includes maintenance https://www.manualslib.com/manual/1090412/Ryobi-Ry09056.html#manual ..

no there is not one here is a link to manual copy and paste https://www.manualslib.com/manual/682035/Ryobi-Ts1552la.html?page=8#manual

Question edited for a lot more clarity and correct the spelling. Videos and parts schematics https://www.google.com/search?q=Ryobi+SS30+trimmer+Fuel+line+diagram ..

They are all the same irrespective of make. ..

The same answer as I replied yesterday. You use a flywheel extractor kit or a 3 legged puller. The flywheel is on a Morse taper with a half moon keyway. https://www.google.com/search?q=Ryobi+RY251PH+trimmer%2C+how+to+remove+flywheel ..And the same videos as yesterday plus one. All the engines are the same as far as flywheels go.

You will need a flywheel extractor that screws into the centre, or a 3 legged puller. The flywheel is on a tapered shaft called a 'Morse Taper' and a half moon key to keep it in the correct position. https://www.google.com/search?q=ryobi+flywheel+extractor

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwiBvqCdx5SCAxXnhYkEHWXLA9oQFnoECBgQAQ&url=https%3A%2F%2Fwww.fixya.com%2Fsupport%2Ft29937314-ryobi_40v_trimmer_ry40009_start_battery&usg=AOvVaw1TJJjlBGwh91eVC5VSM9iD&opi=89978449

Common issues and possible solutions: Fuel-Related Issues: Check the Fuel Level: Ensure that the blower has enough fuel in the tank. If it's running low, refill it with fresh, properly mixed fuel as specified in the user manual. Remember to use the correct fuel-to-oil ratio to avoid engine damage. Inspect Fuel Lines: Examine the fuel lines for any clogs, kinks, or leaks. Clean or replace them if necessary. Clean the Carburetor: A dirty or clogged carburetor can cause starting and running problems. Remove the carburetor, clean it thoroughly, and check for any damaged components. Replace the diaphragm and gasket if needed. Spark Plug Issues: Check the Spark Plug: Inspect the spark plug for signs of wear, fouling, or damage. Ensure it's properly gapped and functioning. If needed, replace the spark plug . Air Filter and Intake System: Clean the Air Filter: A clogged air filter can affect performance. Remove the air filter, clean it, and ensure proper airflow. Inspect the Intake System: Make sure the intake manifold is secure and not loose. Tighten any screws or connections. Heat Soak: Sometimes, backpack blowers experience heat soak, where the engine becomes too hot to start. Allow the blower to cool down before attempting to restart it. Compression and Ignition Coil: Compression Test: Check the engine's compression using a compression tester. Low compression may indicate internal engine issues . Test the Ignition Coil: Ensure the ignition coil is functioning correctly. A faulty coil can lead to starting problems.

J R, Here's a few sites that may help you.... https://www.google.com/search?q=ryobi+40v+trimmer+keeps+shutting+off+at+full+throttle Best to you. Not sure but Tooba apperas to be a Ai Bot.

To install the fuel line on a Ryobi 410r tiller, follow these steps:

1. Prepare the tools and materials: You will need a replacement fuel line compatible with your Ryobi 410r tiller, needle-nose pliers, and a small container or towel to catch any fuel spills.
2. Remove the old fuel line: If there is an existing fuel line, carefully disconnect it from the fuel tank and carburetor. Use needle-nose pliers to loosen any clamps or connectors securing the fuel line in place. Drain any remaining fuel from the old fuel line into a container.
3. Cut a new fuel line: Measure and cut a new fuel line to the appropriate length, ensuring it matches the size and diameter of the original fuel line. It's a good idea to bring the old fuel line to a hardware store to ensure you get the correct replacement.
4. Attach the fuel line to the fuel tank: Insert one end of the new fuel line into the fuel tank's opening. Push the fuel line in until it reaches the bottom of the tank. Make sure it is securely seated.
5. Connect the fuel line to the carburetor: Locate the fuel inlet port on the carburetor. Insert the other end of the fuel line into the port, ensuring it fits snugly. If there are clamps or connectors, secure them to hold the fuel line in place.
6. Check for leaks: Double-check that all connections are tight and secure. Look for any signs of fuel leakage around the fuel line connections. If you notice any leaks, recheck the connections and tighten them if necessary.
7. Test the fuel line: Add fuel to the tank and start the engine to verify that the fuel line is properly installed. Observe the fuel line for any signs of leaks or irregularities while the engine is running.