Greetings,
Please ensure that the clothes are distributed evenly before using another mode to wash your clothes. It might be that there is an issue with only one of your washing modes. If other modes do not show the issue, then I would turn your washer dial counterclockwise by 180 degrees before attempting the first mode again.
Thank you.
One of your parts was faulty on delivery. Due to the cost of control boards, I would always advice a service call so that you get the correct diagnosis and warranty on the part and the labour if it goes wrong. Unscrupulous dealers will sell parts from scrapped machines that haven't been tested. eBay is the worst culprit.
..
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
Question edited for clarity.
I presume you want a WIRING diagram? Not much available for that model. Sometimes you will find the service information in a bag taped behind the bottom kickplate or inside the back of the case.
https://www.google.com/search?q=Kenmore+HE2+110.46502700+wiring+diagram
..
The E2F2 error code on a Kenmore Elite washing machine typically indicates a problem with the communication between the control board and the motor control board. This could be caused by a faulty control board, a loose or damaged wire connection, or a problem with the motor control board.
Here are some steps you can take to troubleshoot the issue:
Unplug the washing machine for a few minutes and then plug it back in to reset the control board.
Check the wire connections between the control board and the motor control board. Make sure they are secure and free from damage.
If the wire connections are okay, you may need to replace one or both of the control boards. You can find replacement parts online or through a local appliance repair shop.
If you are not comfortable working with electrical components, it's best to contact a professional appliance repair technician to diagnose and fix the problem.
Did you check the gauze strainer in the water connector.
To test for voltage, use your multimeter. Turn the machine on and set a cycle, then carefully use the probes to check for voltage.
Question edited for clarity.
LE, not L3?
LE code on Kenmore washer
An LE error code is displayed when the tub fails to spin. The error code indicates that the motor can't operate properly because you've overloaded the washing machine, or a foreign object is stuck in the tub.
Nov 21, 2022
You can determine the age of your appliance by looking at the serial number on the nameplate. The first number indicates the year of manufacture, and the second and third digits indicate the production week.
If the timer on your Kenmore washer is broken, there are a few things you can try to get the spin cycle to run:
Manually advance the timer: If the timer is stuck or not moving, try manually advancing it to the spin cycle. To do this, locate the timer knob and turn it clockwise until it reaches the spin cycle. Once you have manually advanced the timer to the spin cycle, try running the washer to see if it will spin.
Use a multimeter to test the timer: If the timer is completely broken and not advancing at all, you may need to test it with a multimeter. You can find a multimeter at most hardware or electronics stores. Follow the instructions for using the multimeter to test the timer. If the timer is faulty, you will need to replace it.
Use a jumper wire: If the timer is not advancing or you are unable to replace it right away, you can try using a jumper wire to bypass the timer and run the spin cycle. To do this, unplug the washer and locate the wires that connect to the timer. Look for the wires that correspond to the spin cycle and connect them with a jumper wire. Once you have connected the wires, plug the washer back in and try running the spin cycle.
Note: It's important to exercise caution when working with electrical appliances. If you are unsure of what you're doing, it's best to seek the assistance of a professional or to contact the manufacturer for guidance.
t's possible that there is an issue with the door lock mechanism or the door lock sensor. The fact that the door locks but nothing else happens suggests that the washer is not detecting that the door is locked properly. Here are a few things you can try:
Check the door lock mechanism: Make sure that the door lock mechanism is clean and free of any debris or obstructions. Try manually engaging and disengaging the door lock a few times to make sure that it is working properly.
Check the door lock sensor: The door lock sensor is a small switch located near the door lock mechanism. Make sure that it is clean and properly aligned. You can try pressing it manually to see if it is working properly.
Check the wiring: It's possible that there is a problem with the wiring between the door lock mechanism, the door lock sensor, and the control board. Check the wiring harness for any signs of damage or corrosion.
Check the control board: If everything else checks out, there may be an issue with the control board. Make sure that it is properly installed and connected. You may also want to try resetting the control board by unplugging the washer for a few minutes and then plugging it back in.
If none of these steps resolve the issue, it may be best to contact a professional appliance repair service for further diagnosis and repair.
If your Kenmore washer series 400 model 22102 is dripping water in the tub after the cycle is complete, there could be a few potential causes. Here are some things to check:
Water valve: The dripping could be due to a faulty water inlet valve. This valve controls the flow of water into the machine and if it's not closing properly, water can continue to drip into the tub even when the cycle is complete. You may need to replace the water inlet valve to fix the issue.
Water level sensor: Another potential cause of dripping could be a malfunctioning water level sensor. This sensor tells the washer when the tub is full and it's time to stop filling with water. If the sensor is faulty, it may not be accurately detecting the water level, which could lead to dripping. You may need to replace the water level sensor to fix the issue.
Drain hose: If the washer is not properly draining, it could also lead to dripping after the cycle is complete. Check the drain hose for any kinks or clogs that could be preventing water from draining properly. You may need to clean out the drain hose or replace it if it's damaged.
Overloading: If you're overloading the washer with too much laundry, it could be causing water to overflow and drip into the tub after the cycle is complete. Make sure you're following the manufacturer's guidelines for load size to avoid overloading the machine.
If you're unsure of how to diagnose or fix the issue, it may be best to consult a professional technician or reach out to the manufacturer for assistance.
There could be several possible causes for your Kenmore top load washer not agitating or spinning. The actuator is one possibility, but it's not the only one. Here are some other potential causes to consider:
Lid switch: The lid switch is a safety feature that prevents the washer from agitating or spinning when the lid is open. If the switch is faulty, it may prevent the washer from agitating or spinning even when the lid is closed. You can test the switch by using a multimeter to check for continuity when the lid is closed.
Drive belt: The drive belt connects the motor to the transmission, which turns the agitator and drum. If the belt is broken or worn, the washer won't agitate or spin. Check the belt for signs of damage or wear, and replace it if necessary.
Motor coupler: The motor coupler connects the motor to the transmission. If the coupler is broken or worn, the washer won't agitate or spin. You can check the coupler by removing the motor and transmission and inspecting the coupler for damage.
Transmission: If the transmission is faulty, it may prevent the washer from agitating or spinning. This is a more serious issue that may require a professional repair.
Based on the symptoms you described, the issue could be with the actuator, but it's hard to say for sure without further testing. The actuator controls the shifting of the transmission from agitate to spin, so if it's not working properly, it could prevent the washer from agitating or spinning. You can test the actuator using a multimeter to check for continuity.
If you're not comfortable diagnosing or repairing your washer yourself, it's best to contact a professional appliance repair service to diagnose and fix the issue.
