20 Most Recent GE Spacemaker GTUP240EMWW 24" Electric Laundry Center with 2.2 cu. ft. Washer, 4.4 cu. ft. Dryer, 9 - Page 2 Questions & Answers

The TRADESMAN Auto Rotisserie is perfect for body shops, race car fabrication, and classic car restoration. However, it is built for the professional shop or serious do-it-yourself. This equipment is all about saving time and money and working safer and more intelligently.

Repairing a washing machine can be a complex and potentially dangerous task. It is recommended that you have some experience with repairing appliances before attempting to disassemble and repair a washing machine. Here are the general steps for taking apart and repairing a 1984 GE top-loading washing machine:

1. Unplug the washing machine from the power source and turn off the water supply to the machine.
2. Locate the screws that hold the control panel in place, typically found on the back of the machine. Remove the screws and carefully lift the control panel up and away from the machine.
3. Locate the cabinet clips that hold the cabinet in place, usually found at the top of the front panel of the machine. Use a flathead screwdriver to push the clips inwards and release them from the cabinet.
4. Tilt the cabinet forward and lift it up and off of the washing machine. Place the cabinet aside.
5. Locate the pump, motor, and transmission assemblies at the bottom of the machine. Check for any signs of damage or wear and tear, such as broken belts or damaged bearings.
6. If you need to replace a part, carefully remove the old part and replace it with a new one.
7. Once the repairs are complete, carefully reassemble the machine by following the above steps in reverse order.
8. Turn on the water supply and plug the machine back in to test it.

If you encounter any issues during the repair process or are unsure about how to proceed, it is recommended to seek the assistance of a professional repair technician.

There are a few actions you can take in the troubleshooting process if your GE washer, model GFAN1000L2WW, won't start: Verify the power source: Make that the washer is connected correctly and that the outlet is working properly. To test it, try connecting another device into the outlet. Inspect the door latch: If the door latch on the washer is not correctly engaging, the washer might not start. Verify that the latch is correctly engaging and that it is clean and debris-free. check the control panel: Verify that the appropriate cycle is selected on the washer's control panel and that all essential buttons and switches are turned on. The washer might not start if the water supply is not working properly. Verify the hoses are not kinked or clogged and that the water supply valves are turned on. Verify the motor: If none of the aforementioned fixes the issue, the washer's motor might be at fault. A qualified repair specialist may be needed to diagnose and resolve this. If you are unable to identify the problem or fix it yourself, it may be necessary to contact a professional appliance repair technician for assistance.

Check to see if a circuit breaker has tripped.There might be something wrong with the outlet.Maybe the washers motor might of had overheated.

The correct value of the brake resistor circuit for your GE washing machine may vary depending on the specific model and other factors. However, according to some sources, the typical resistance for a GE washing machine brake resistor circuit is around 25-30 Ohms. If you are measuring 47 Ohms, this could indicate that there is an issue with the circuit, which could be causing the error code and the problem with the spin cycle. You may want to check for any loose connections or damaged components in the circuit, and consider replacing the resistor if necessary. If you are not comfortable with electrical repairs, it may be best to contact a qualified technician for assistance.

If your GE GFW650 front-load washer is skipping directly to the end of the cycle without spinning the clothes dry, there are a few possible causes that you can investigate:
1. Unbalanced Load: If the load of laundry is not evenly distributed in the drum, the washer may not be able to balance it properly during the spin cycle. This can cause the washer to skip the spin cycle and go directly to the end. Try rearranging the clothes in the washer and restarting the cycle.
2. Blocked Drainage: If the washer is unable to drain water from the drum, it may skip the spin cycle and go directly to the end. Check for any blockages in the drainage system, such as a clogged drain hose or filter. Clean or replace any blocked components.
3. Faulty Motor: If the motor that drives the spin cycle is malfunctioning, it may cause the washer to skip the spin cycle and go directly to the end. This is a more serious issue that may require a professional repair.
4. Malfunctioning Control Board: If the washer's control board is malfunctioning, it may not be able to properly control the spin cycle. This can cause the washer to skip the spin cycle and go directly to the end. Again, this is a more serious issue that may require a professional repair.

If none of these solutions work, or if you are uncomfortable performing any of the troubleshooting steps, it may be best to contact a professional technician to diagnose and repair the issue.

The drain hose might be either punctured or is loose or the drain pump is not working or the tub to the pump hose is broken.

It should be connected right next to the drain hose.

The red flashing light on the circuit board of a GE washer is often an indication of an error code or fault. The error code can help diagnose the issue. Here are some common causes of a GE washer not spinning and a red flashing light on the circuit board:

1. Door lock error: Ensure the door is securely closed and latched.
2. Drive belt issues: Check if the drive belt is broken, stretched, or has come off the pulley.
3. Motor issues: The motor may have failed or the wiring may have come loose.
4. Central control unit (CCU) issues: The CCU may have failed and will need to be replaced.

If you are unable to diagnose the issue, it is recommended to have a professional technician diagnose and repair the problem as it may require technical skills and specialized tools.

Try a motor reset. This is the electronic washer. Unplug for two minutes, plug it in then open and close lid 7 times. This will reset motor. Also make sure belt is not broken. https://www.google.com/search?q=GE+front+load+Washer+WBVH6240+BEEPS+TWICE ..

The light is part of the diagnostic system. This is an internal systems light that flashes all the time and is an indication that everything is operating normally.

When you took the hot water hose off, did you check the little gauze strainer inside where the hose screws? That black in the water is iron and scale from the hot tank. See the video I added. Cleaning the filter https://www.google.com/search?q=ge+profile+top+load+washer+clean+filters Videos for removing the agitator https://www.google.com/search?q=ge+profile+top+load+washer+remove+agitator Buzzing could be the motor or controller knob, but if its' running, don't worry. https://www.google.com/search?q=ge+profile+top+load+washer+buzzing+noise Screeching is normally belt slip. You can get a can of belt conditioner which makes it supple and grippy. A GE washer making noise that sounds like squealing likely has a damaged drive belt. This rubber belt is suspended on a pulley, connecting the tub to the drive motor or transmission in front and top load washers. Wear and tear can cause the belt to loosen or fray, resulting in a squealing sound. May 1, 2021

Why Is My GE Washer Making Noise?

it might spin off try holding drum and turning

It sounds like there may be an issue with the drain hose on your GE 465 top-load washer. The fact that the drain hose is wet halfway up suggests that there may be a leak in the hose. This could be caused by a hairline crack or a problem with the connection between the hose and the drain outlet. One possibility is that the extra rinse option and the maximum water level setting on the tub caused a higher volume of water to be drained through the hose, which may have caused an existing issue with the hose to become more pronounced. Another possibility is that the internal drain pump is not functioning properly and the water is not being pumped out of the machine properly, causing the overflow. It is recommended to contact the manufacturer's customer service or a professional technician to have the washer inspected and repaired. They can check the hose and connections, and also the drain pump to determine the cause of the problem and fix it accordingly. It's important to keep in mind that attempting to repair a washer can be dangerous if you're not familiar with the proper procedures and safety precautions. It's best to let a professional technician handle the repair. Regenerate response

The hose could be kinked or have a hole in it for the washing machine and you need a new hose as well for your washing machine..Or the drain pump is bad or the tub to the pump hose is not working.

If the inlet on your GE washer has been stripped or cross-threaded, it may be necessary to replace the inlet to repair the problem. To replace the inlet on your GE washer, you will need to follow these steps:

1. Disconnect the power to the washer by unplugging it from the wall outlet or turning off the circuit breaker that supplies power to the washer.
2. Shut off the water supply to the washer.
3. Remove the hoses from the inlet by loosening the hose clamps or fittings that secure them to the inlet.
4. Remove the screws or bolts that secure the inlet to the washer.
5. Carefully lift the inlet out of the washer and set it aside.
6. Install the new inlet by reversing the above steps. Make sure to connect the hoses to the correct fittings on the new inlet.
7. Turn the water supply back on and check for any leaks.
8. Restore power to the washer by plugging it back into the wall outlet or turning the circuit breaker back on.
9. Test the washer to make sure it is filling properly with the new inlet.

Note: These instructions are general guidelines and may vary depending on the specific model of your GE washer. If you are unsure of how to replace the inlet on your washer, it is recommended that you contact a qualified appliance repair technician for assistance.

If you have replaced the door lock on your GE washing machine and it is still not working properly, there could be a few different causes for the issue. Here are a few things you can try:

1. Make sure the door lock is properly installed and aligned with the latch on the door.
2. Check the wiring between the door lock and the control board to make sure all connections are secure and there are no damaged wires.
3. Test the door lock with a multimeter to see if it is receiving power and functioning properly.
4. If the door lock is receiving power and functioning properly, the issue may be with the control board or another component in the washing machine. In this case, it may be necessary to take the washing machine to a repair shop or contact the manufacturer for further assistance.

It is also a good idea to make sure that the door lock is not being activated by any foreign objects or debris that may be preventing it from functioning properly.

need the Model number to help you find the white tag and add the model number it inside the front door frame

Breakers trip if there is a dead short to earth or if something in the appliance has high resistance and is drawing more amps that the breaker. This can happen with failing elements. However F72 is leading towards a control board issue. This needs professional diagnosis as they are expensive. https://www.google.com/search?q=GE+ZET1FH1S+Wall+Oven+Error+code+F72 ..

First thing to do is unplug it for 5 minutes and see if it resets.