20 Most Recent Intel D845PT (KD845PTPAK10) Motherboard Questions & Answers

If you formatted the hard drive, you'll need to put the install disk in the CD to install Windows. But first make sure your machine is set to boot from the CD before it boots from the hard drive. You can do this from the setup menu (I think in an e-Machine you hit DEL or one of the special function keys on startup). Go to the startup option and set the CD as the initial boot device.Your system may also offer the opportunity to press a special function key on startup to change the boot order for one time only.

aticus,

Intel Support > Intel D845PT Technical Product Specification,

http://www.intel.com/support/motherboards/desktop/d845pt/sb/cs-013219.htm

Under the heading - Technical Product Specification, left-click on the blue -
A7585201.PDF

The computer you are using now has Adobe Reader on it. Adobe Reader uses PDF files.
I would recommend however, updating to Adobe Reader X (10), though, if the computer doesn't have this version.

After you click on the above file name it may take up to 30 seconds, (Or more), for the first page to come up.
It may also take additional time for the file to fully download.

Using the Down Arrow at the top, and the page number box to the right of it, go to Page 71.

{Or alternatively left-click in the page number box, to the right of the Down Arrow at the top of the PDF file.
The number in the page number box will be highlighted in blue.
Type 71
Now press the Enter key }

D points to the Front Panel header.

The Front Panel header is a rectangular block, and is vertical in this illustration.
Turn the illustration in your mind, clockwise to the right.

Processor to the top, Ram Memory to the right, PCI slots (White) to the bottom.
The way it sits in your computer.

The Front Panel header now sits horizontal, and is parallel to the bottom edge of the motherboard.

There are 16 pins in the Front Panel header.
8 across the Top, and 8 across the Bottom.

The pins on Top are numbered ODD.

Starting at the Right side, (Closest to the CMOS Battery), going towards the Left, on the Top row;
Pins 1, 3, 5, 7, 9, 11, 13, and 15.

Starting at the Right side going towards the Left, on the Bottom row;
Pins 2, 4, 6, 8, a space, pin 12, a space, and pin 16.
There is NO pin 10, or 14. Just a space where these two pins would be.

A) Pins 1 and 3 are for the HarDDrive Activity LED light.
(HDD LED)
Pin 1 is for the Positive wire.

If the HDD LED light is dim when operating, switch the wires around.

B) Pins 5 and 7 are for a Reset switch, IF a Reset switch is used.

C) Pins 9, 11, 13, and 15 are NC. Not Connected.

D) Pins 2 and 4 are for the Power On LED light.

E) Pins 6 and 8 are for the Power On switch.

F) Pins 12 and 16 are NC. Not Connected.

For additional questions please post in a Comment. (Believe upper right of your page - Comment)

Regards,
joecoolvette

which is it your dvd rom or your hard drive that its not detecting

Test your PSU or replace it if your power supply units fan is not working your PSU is faulty

One bad lead can cause a computer to continue on a cycle or to shutdown or fail to detect/ boot up a computer hard drive

Test all leads that attach to your hard drive including electrical extensions,IDE,SATA

the leads from your "((MOTHERBOARD TO YOUR HARD DRIVE))" make sure they have a secure connection and are not faulty or just replace them they could be faulty make sure all leads that are attached to your drives dvd\cd 3 1/2 inch floppy have secure connections and are not faulty even the electrical extensions or just replace them they could be faulty a computer needs its connections to continue its cycle and have an end so any faulty leads will end up with a computer error even something as small as a faulty electrical extension or fan lead can cause this problem hope this helps

Hi Again,

I guess you posted your question twice, but just in case, here's the same solution:
Yes, that board is only a 1.1 USB port. USB 2.0 can easily be added to a computer using a USB 2.0 PCI card. These cards are relatively cheap and they can be found in almost any computer store. You can even find USB 2.0 PCI cards at Walmart. The cards will typically have 3 - 5 ports on them. These ports are setup so that you will have to plug your USB devices into the back of the computer.

Good Luck

Mark

HI,

Yes, that board is only a 1.1 USB port. USB 2.0 can easily be added to a computer using a USB 2.0 PCI card. These cards are relatively cheap and they can be found in almost any computer store. You can even find USB 2.0 PCI cards at Walmart. The cards will typically have 3 - 5 ports on them. These ports are setup so that you will have to plug your USB devices into the back of the computer.

Good Luck

Mark

you should enter your motherboard manufacture website and dawanload new version

Reseat all cards in system, including the RAM. If it still does not boot try removing one stick of ram at a time to see if it boots. As well as removing extra cards.

BIOS has no upgrade for VISTA to be installed. Contact the manufacture to write on update BIOS for that computer or motherboard as the case may be.

recheck that the memory has been reinstalled properly... if it has and you have the same issue swap the memory to the opposite slot(s) it is in.

You can reset it through the HP recovery manager. First, turn off your laptop and restart it while pressing the F11 key. Then, select System Recovery, and follow the on-screen instructions to reset your HP laptop password. After that you will be able to log into your laptop again. This is one Answer But you will find various ways. Google Forgot windows 7 password on my notebook & you'll be surprised what appears. YouTube also. Hope this helps

The best way to prolong life of a computer is to blow out dust from the case and cooling fins and power supply regularly, at least every year. That prevents overheating - a primary cause of component failure. Do not overclock. Do periodic full disk backups and intermediate new file ones. Leapfrog between two external disks. They are cheap. Protect them from fire. Laptops - same story,, do not block cooling holes by putting on a blanket while lounging. And turn off machine before blowing out dust. Do not use full PSI compressor air! maybe 20 PSI...

MAC uses RAW/APFS etc and Intel uses full format DOS based. Not compatible.

If your Intel D865GVHZ motherboard is not booting and you've tried replacing the CMOS battery, resetting it, reseating RAM, and changing the PSU, it may indicate a more serious hardware issue. You should consider checking the following: 1. Check the monitor: Ensure that the monitor is functioning correctly by trying it with another computer. 2. Check the connections: Verify that all cables, including the power and video cables, are securely connected. 3. Inspect for hardware failures: Check for any visible signs of hardware damage or loose components on the motherboard. 4. Test with minimal hardware: Disconnect all unnecessary peripherals (e.g., external drives, graphics cards) and leave only the essentials connected (CPU, RAM, power, and monitor) to rule out any conflicts or faulty hardware. 5. Try a different RAM: If possible, test with different RAM modules to rule out faulty memory. 6. Listen for beep codes: If your motherboard has a speaker, listen for any beep codes during startup, as they can provide clues about the issue. 7. Inspect the CPU: Check the CPU for any damage or bent pins, and ensure it's seated correctly. If none of these steps resolve the issue, it's possible that your motherboard or other critical components may have failed, and you may need to consider a replacement or professional diagnostics to pinpoint the exact problem.

Intel Smart Response Technology (SRT) is used for SSD caching to improve system performance. To use it successfully, here are some steps to consider: 1. SSD Compatibility: Ensure that your SSD is compatible with SRT. It should be a SATA SSD. 2. BIOS Settings: In the BIOS, set the SATA mode to RAID (not AHCI or IDE) before configuring SRT. Make sure your motherboard supports SRT as well. 3. Driver Installation: Before enabling SRT, install the latest RAID drivers provided by your motherboard manufacturer. 4. Backup: Backup your important data because enabling SRT involves data migration. 5. Enable SRT: In the BIOS, set the SRT mode to "Enhanced" or "Maximum" depending on your preference. 6. Initialize SSD: Initialize and format the SSD through Windows Disk Management. 7. Install Intel RST: Download and install the latest Intel Rapid Storage Technology (RST) driver and software for your chipset. 8. Enable SRT in RST: Open the Intel RST software and enable SRT. You should see an option to accelerate your HDD with your SSD. 9. Reboot: After configuring SRT, reboot your system. 10. Verify: Check if SRT is working by opening the Intel RST software. It should show your SSD as a cache for your HDD. If you're encountering crashes or issues, it's essential to ensure compatibility and follow these steps carefully. If the problem persists, consider seeking assistance from your motherboard manufacturer's support or Intel's support, as it could be related to specific hardware or software conflicts.

They don't like being dropped. A connection of likely dislodged, or the screen is broken if you don't see anything at all.

The end part of your question makes it sound like an advert.Download and run the Free version of CCleaner. Remove TSR (terminate and stay resident) programs on start up. These are the programs that run in the background.Download CCleaner 6 For Free - Make Your PC Faster & Saferccleaner.comhttps://www.ccleaner.comClean Temporary Files, Optimize & Speed Up Your Computer. Download Now. The No. 1 Tool for Cleaning Your PC. Download CCleaner now. Browse Solutions. View Products. Multiple Payment Options...

microsoft word is just a word processor. more expensive the works. microsoft works contain a word processor, spreadsheet, database program. word has more features but cost more. works is old program check to make sure it works with your os.

There are several possible reasons why your Intel D915gav motherboard won't turn on, even though the green LED on the motherboard is on. Here are some troubleshooting steps you can try:

1. Check the power supply: Make sure the power supply is turned on and connected properly to the motherboard. Verify that the power cable is securely plugged into the wall socket or power strip and into the power supply unit. Also, check if the power supply is providing the correct voltage to the motherboard.
2. Inspect the RAM: Check if the RAM is seated properly in the slots. Remove the RAM and re-insert it, ensuring it's seated firmly in place. You can also try booting with one RAM stick at a time to see if one of them is faulty.
3. Check for loose connections: Check all cables, connectors, and wires to ensure they are properly seated and secured. Make sure there are no loose wires, frayed cables, or damaged components.
4. Test the power button: If the power button on your computer is not working, the motherboard won't turn on. Try connecting the power button pins directly to the motherboard to see if it turns on.
5. Clear the CMOS: Try clearing the CMOS memory to reset the BIOS settings. This is done by removing the CMOS battery for a few minutes, then re-inserting it and restarting the computer.
6. Check the CPU: Make sure the CPU is seated correctly in the socket and that there is no thermal paste residue between the CPU and the heatsink. If there is, clean it off and reapply fresh thermal paste.

If none of these steps resolve the issue, it's possible that the motherboard or another component has failed and may need to be replaced.