Top 20 GE PFSS9PKy Refrirator Questions & Answers

Resetting your Refrigerator filter indicator light after changing your water filter

Some people are not aware that after you change your refrigerator water filter, there are two more steps that should be taken to complete the water filter change process.

Step 1:Reset your water filter indicator light - Most new refrigerators come equiped with an indicator light that notifies you when it is time to change your water filter. This light does not automatically reset when you change your water filter. Here is a list of refrigerator manufacturers and how to reset the indicator light.

GE General Electric Refrigerators - Press and Hold the Reset Button for around 8 Seconds.

Step 2:Flush a couple of gallons of water through your new filter. Since most refrigerator water filters are made of carbon, some carbon residue is present in the first gallon or two of water. This will leave a bitter taste and residue in your water. If you continue to have these problems after flushing a couple of gallons through the filter, it is possible that you have a defective water filter.

To remove the ice tray from your GE refrigerator model GFSF6KEX, follow these steps: Empty the Ice: Before removing the ice tray, empty it of any ice cubes. This will make it easier to handle. Locate the Ice Tray: The ice tray is typically located in the freezer compartment, usually near the ice dispenser or ice maker. Grasp the Bottom Edge: Stand in front of the freezer and open the door. Grasp the bottom edge of the ice tray on the sides. Be cautious not to place your fingers near the opening at the bottom front part of the bucket where the crusher blades are located. Lift Up the Front: Lift up on the front of the ice tray so that it clears the stops on the ice bucket rail. Pull the Tray Forward: Pull the ice tray forward and out of the freezer compartment. Reinstalling the Tray: To reinstall the ice tray, follow these steps: Line up the flange pieces on the sides of the tray with the channels in the ice bucket rails. As you push the ice tray all the way back, lift the front of the tray so that it clears the stops on the front of the ice bucket rails. Verify that the tray is properly inserted by pulling it forward. It should hit the stops on the rail and not come out. If it does, push the tray further back. Check for Misalignment: If you're unable to push the ice tray all the way back, it might be due to a misalignment between the back of the auger (located in the tray) and the prongs on the auger motor (mounted in the back freezer wall). To fix this: Remove the ice tray. Close the freezer door. Press the dispenser for cubed or crushed ice; you should hear a snap. Open the door again and reinstall the ice tray. Remember to handle the ice tray carefully, especially if it's full of ice.

Page 9 of the manual, back upper right corner https://products-salsify.geappliances.com/image/upload/s--dJG7xmc1--/85553cf15b3719905b992ef19e49bbcc339c121d.pdf All the specs in the maker page Water Filtration GE Water Filtration MWFP https://appliances.monogram.com/us/specs/ZISW360DM#specifications-and-files ..

See troubleshooting tips on page 26 for help GE PYE22KYNFS user manual (English - 98 pages) (manuals.co.uk)

Question edited for a lot more clarity. Question moved from GE Ranges to GE Fridges. Sabbath Mode stays on until you turn it off. Press and hold the Lock and Light button simultaneously for 3 seconds to enter and exit the Sabbath Mode.

Bottom Freezer Refrigerator - Setting Sabbath Mode

GE Appliances https://products.geappliances.com > appliance > gea-supp...

Explanation of the Sabbath Mode Feature

GE Appliances https://products.geappliances.com > appliance > gea-su... Refrigerators with a Sabbath Mode feature puts the refrigerator in a timed defrost mode. It also turns off the icemaker, dispenser, and control touch screens. ..

The Technical Service Manual says it is help by 3 magic slotted fasteners! Plus some RTV 102 seal which is this

Momentive RTV102 Adhesive/Sealant rtv 102, 2.8 fl oz ...

RSHughes https://www.rshughes.com > rtv102_white_3tg Momentive white RTV102 adhesive/sealant with a 72 hr cure time. Provides a 20 min fixture time. Delivers great performance with a shear strength of 200 psi, ... US$7.84 · ‎In stock Service Manual Page 24 https://www.manualslib.com/manual/739574/Ge-Zic36on-Series.html?page=24#manual //

Question edited for clarity and toss in some CAPS. https://www.google.com/search?q=ge+ice+maker+model+opal01gepkt+filter+replacement I watched a video last night of a lady who took the side cover off and used a pipe brush to clean the black mold residue out of the pipes. I was pretty gross back there and she said it was only a year old. Check the side where the water connection is. https://www.youtube.com/results?search_query=clean+GE+ice+maker ..

May be best to call the repairman.

There could be several reasons why the internal lights in a vehicle may not be working while the panel lights are functioning. Here are a few possible explanations:

1. Blown fuse: Check the fuse box to see if the fuse for the interior lights has blown. If it has, replace it with a new one of the same rating.

2. Faulty light switch: The switch that controls the interior lights may be faulty or worn out. Try toggling the switch on and off to see if it makes any difference. If not, consider replacing the switch.

3. Loose or corroded wiring: Inspect the wiring connections for the interior lights. Loose or corroded connections can disrupt the electrical flow and prevent the lights from working. Tighten any loose connections or clean off any corrosion.

4. Burnt-out bulbs: If all the interior lights are not working, it's possible that multiple bulbs have burnt out at the same time. Check the bulbs and replace any that are no longer functional.

5. Dimmer switch settings: Some vehicles have a dimmer switch that controls the brightness of the interior lights. Make sure the dimmer switch is not turned all the way down or set to a very low level.

If none of these solutions resolve the issue, it may be best to consult a professional mechanic or electrician to diagnose and repair the problem.

yes it does

https://products.geappliances.com/appliance/gea-support-search-content?contentId=22067 https://www.youtube.com/watch?v=LOYwkydARlY

March 2007 and the 17th produced that month. 03(month of)07 KR(range)(number)00017 (produced)

Possibly too hot and is cooling the condenser.

copy and paste link https://products.geappliances.com/appliance/gea-support-search-content?contentId=34403

If you are referring to the ice maker or cold water dispenser, than check the fill solenoid.

your not going o see a light use a dollar bill or paper to test close door on paper should be unable to remove the paper go around the door testing --door my be in need of adjustments or hinge worn down

Question edited for clarity and correct model nomenclature. The link says is it part of the motherboard features and not a standalone unit https://www.google.com/search?q=GE+GSL25JFPABS+location+of+defrost+timer ..

It's possible that the fan blades are hitting ice, frost, or debris, causing the noise. The fan might also be struggling to turn if there's any obstruction or if it's damaged

Jason, Have looked over the net for parts but can't find any. Did find this replacement head.... https://www.ebay.com/itm/266329193858 Looking at the 3d and 4th picture, it appears that the valve is attached by the 4 screws. It's possible some sand or debris may be on the seal keeping it from closing fully. If you turn the water off and drain down the whole house by opening the lowest faucet and openimg a high faucet. Possibly you could then remove the valves 4 screws and clean it. If you have shut offs on both sides of the filter you can just shut those. There's just no blow up diagram of internal parts so it maybe a ball valve that has a nick in it and taking it apart won't help. Sorry I can't be of more help...but that's what I'd do if it was mine. Best to you.