20 Most Recent
RCA HD52W56 52" Rear Projection HDTV - Page 4 Questions & Answers
I need a power supply
wow, good luck with this one, many repair shops end up with these tv's and the owners don't want to bother with them when they find out how much it will cost to fix them. that being said, get on the phone and call a few and you may find just what you need, another alternative is of course the internet (try sears parts store), or Ebay, hope this helps. I like you fix old stuff and enjoy bringing things back to life. good luck
I have a 52 RCA
This RCA projection tv model have known to have many parts of capacitors components are dying and dead on the tv power supply board.That the board section where the tv power a/c cord plug into it.U have all the tools and can do bsaic soldering work too?Yes,try website like Tvrepairworld.com to buy the capacitors compponents set they put together and replaced all these capacitors parts on the tv power supply board section,will solved this problems.
Blurred pictures,displays green,red colors on
Go to Menu then setup Look For Convergence,If you Do Not see Convergence in the Menu then you have a Blowed Fuse on The deflection Board FL231.
Deflection Board is the Bottom Left hand side board that has (FBT) flyback Transfomer on it.
If you are Not able to repair it yourself ,then you can ship Board to PTS for repair.
1-800-844-7871
Tv is pink and green
Problem might be in the Deflection board, Look for Bad Capacitors CP150,CP114,CP120, they will be swollen or vented on Top.IF you find CP150 Bad make sure you replace all 3 caps.
If you cannot solder or read a voltohm meter then you can either replace the deflection board or have yours rebuilt.
PTS rebuilts boards 1-800-844-7871
UED has replacement boards 1-800-648-6657
RCA rear projection hd tv
Hello,
Your power supply board is dead, u know basic electronics' and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get your TV power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.
Hope this will help in solving the product.....
Smelled smoke and hot wires, tv went off and never
Thats a 27K 1/2 watt Carbon Composition resistor 5% tolerance. You got deflection issues so a replacement resistor will most likely fail unless you discover whaich componenet on the deflection board caused the resistor to burn. The deflection boards have been discontinued for your model which has the ATC321 chassis. But you can get a remanufactured ATC321 deflection board from
www.tvrepairworld.com
The tv worked fine last night but now will not
most likely its on the deflection power supply board possible flyback failure or caps in power supply if you have the tools and can solder you may want to try to take this project on
or you may want to contact a local servicer in your area usual cast to repair the module is 180.00 to 240.00 in our area and that wll vary to the area you are in
No audio
ok sound on the rca itc222 chasis comes ofd one curcit board. This board is called the small signal board. but before we get this replaced we have to elemate a few things. one check you audio setings and make sure the amplifer is set to internal. also you speakers could have blown. and the connectors to speaker unlikely be loose. If these items are elemanted then the small signal board. a item that only technicians can replace. they have special computer interface they use to download data from the old to a new board when they replace it
I have a RCA 52"
This happens all the time. It just might be fixable. This connector is known as the "f" connector or female coaxal connector. Most average electronics technician can fix them. This connector is attached to a component called the tuner. The tuner is what takes the signal and selects the channel the tv recieves. To replace the connector it means removeing the cuircit board that the tuner is on and then removeing the tunner, disasembling the tuner. Now until you find a good tech, there is another option... take an vcr and use the rca inputs on set. essitally tunning the set through the vcr. Now you will have to change channels through the vcr. but it will work. also there is a chance that the tuner might be damaged. just depends on the damage that occured when the connector was broke off..,let me know if you need any more help
I turn my hd52w56 52in
This occurs because there is no power reaching the screen. The power supply has been kind of ruptured or is not supplying enough current to the screen. This is due to a faulty converter. Your screen might have been damaged due to uncontrolled current to the screen. I advice you replace the screen or see a specialist, okay. Hope these help.
The heads are cut off....I
How did this start? you need the remote to change the settings in the first place, somebody used it to change the settings! Have you tried using the dish remote, did you change the format on dish? there is a place on the remote that changes the format from the sat signal also, should be a yellow bar below the live TV button. This is the way mine is set up but on other remotes there is still a button to change the format, look on the dish remote for this.
The projectors are not aligned
you are haveing convergence problems. first is determine if you can align this using the menu. try going into customer main menu and going into setup there should be a option called convergence if you do not have this option you might have what is commonly called the fl231 fuse problem and you need to read the artilcle on this simple repair. http://www.fixya.com/myprofile/tips.aspx?usrid=214751 convergence can be simple or can get difficult.
Not finding what you are looking for?