20 Most Recent LG WT1201CV 4.5 cu. ft. Ultra Large Capacity Top Load Washer with Fron - Page 6 Questions & Answers

If its flooding when the machine is off and water is still going into the machine, the inlet valves will be the fault. If its flooding when in use, there is a blockage or failure of the pressure switch or the pressure tube. These control the water level in the machine.

LG Washing... | Answered on Jun 16, 2019

This suggests a problem with the motor, the bearings or the suspension rods that hold the tub basket. In some cases, it could be caused by an object between the inner basket and the outer tub. The unit detects too much force on the motor or uneven forces as it spins and slows down even when empty. When there is a load, the washer stops to protect the system.

First try lifting up the inner basket and turning it a small amount. If this is difficult, one or more of the suspension rods and associated hardware should be checked and the damaged parts replaced. Check for and remove foreign objects between the basket and tub. Finally check the motor, motor shaft and bearings to determine which parts need to be replaced if the problem isn't corrected in the above steps.

I hope this helps.

Cindy Wells

LG Washing... | Answered on Jun 07, 2019

Probably something fallen out of clothing and catching on the drum.

LG Washing... | Answered on Jun 06, 2019

Check belt and belt tension switch.

LG Washing... | Answered on Jun 04, 2019

if it is still under warranty you may wanna check their online customer service representative for home service. If not under warranty then you can do DIY as long as you can follow the disassembly steps and as long as you know some basic electronics testing. Look for the pressure sensor switch. Let it check for its continuity through multimeter. This part can be removed on the machine if you dont know how to test then ask your nearest technician to do the testing.

LG Washing... | Answered on Jun 02, 2019

Hold button for 3 seconds

LG Washing... | Answered on May 29, 2019

The serial number should be on the back side of the washer, on a silver label near the top.

LG Washing... | Answered on May 24, 2019

On my WT1501CW it was a leaky inlet valve. part #5221EA1008F. It was dripping water into the floor. I found the issue by removing the top rear panel. This exposed that the parts around where the hoses connect were wet on the inside. I remove the inlet valve with the hoses still connected and turned on the water and small mists of water were coming out of the plastic. Hope this helps someone

LG Washing... | Answered on May 24, 2019

complete top of machine needs to be removed and the pulsator under that is a big nut once removed the drun will come out

LG Washing... | Answered on May 22, 2019

Solution. Unplug the machine. Hold the power button for 10 seconds. Plug back in. Push the power button and the washer should turn on. Walk away leaving the machine on. When I did this, I came back to find the drum light off and machine would start on command now. Good luck.

LG Washing... | Answered on May 20, 2019

Google (LG)(WD-80300NUP)(manual) without parens.

LG Washing... | Answered on May 17, 2019

Not finding what you are looking for?
LG WT1201CV 4.5 cu. ft. Ultra Large Capacity Top Load Washer with Fron Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers


Level 3 Expert

85223 Answers

Cindy Wells

Level 3 Expert

6073 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

LG Washing Machines

  • LG Washing Machines

Most Popular Question

lg tromm washer model wm2277hw

  • Washing Machines