20 Most Recent ESCHMANN Little Sister Autoclave Tabletop - Page 3 Questions & Answers

They may be contaminated during sterilization by using autoclave

They make test strips.

Manuals are available from PHC. Email [email protected] or call Technical Support at 800-858-8442 ext. 48299

Plumbing problem - White Goop: If your water is too hard, soap may not be dissolving completely, so creating a 'cloud' of macroscopic particles.

As water freezes the molecules it is made from become a rigid framework. Think of it like scaffolding poles. they take up a lot less space when the are all in a pile but they take up a lot more space when you bolt them together.

Hello, Debra - Apparently the company Education Insights sells the GeoSafari Talking Microscope. If you have not already done so, I suggest you contact Education Insights Customer Service and ask about the availability of the slides you need. You can find the Customer Service toll free phone number and email address here: https://www.educationalinsights.com/category/customer+service.do Best wishes.

https://www.zigya.com/competition/neet/study/ https://www.zigya.com/competition/neet/study

https://sciencestruck.com/microscope-diagram-functions

George tang ,,,, here is drive.. follow the link download and run in your system with regards it will look like so Aigo GE-5 Driver Created by Olli Niemitalo on 2014-01-31, last modified 2014-01-31 I bought an Aigo GE-5 microscope years ago. If someone needs, here is the driver for it. GE5-mikroskooppi.zip Thanks to Pauli for salvaging this from the CD my CD drive could no longer read. http://yehar.com/blog/?p=3468

But a new scope. Having the crosshair reseated will cost you more than getting a new BSA scope.

Manuals are available from PHC. Email [email protected] or call Technical Support at 800-858-8442 ext. 48299.

Check the fuses located on both sides of the mains connection in the back of the autoclave. One of them has blown. If both check ok, then check the connection tho the mains. You may have a faulty ground. If you are not comfortable doing this, contact Eschmann at tel:+44 (0)1903 753322 Fax: +44 (0)1903 875789 [email protected]

If you're clever with electronics and can solder, consider an LED replacement. Do you have any data on the voltage, current, or lumen rating of the bulb?

Choosing the right laboratory for conducting various tests and analyses can be a tricky affair. If there is any discrepancy in readings, it can be cause quote a stir. Thus, it is imperative that the staff operating the equipment of the laboratory must be expertly trained. The equipment itself must be top notch in quality. LiveScanLabs has managed to meet all this criteria. They have centers in Hialeah, Hollywood, Fort Lauderdale, Pembroke Park and Pembroke Pines. They conduct Fingerprint Analysis, Fingerprint Testing, **** Analysis, **** Testing, DNA Analysis, DNA Testing and regular health tests as well. Visit their website at www.livescanlabs.com.

Are you sure that the lid safety interlock switch isn't damaged/dirty? If the centrifuge can't detect that the lid is closed it will never start. Sometime it just needs an extra push down on the lid.

It sounds like either the bulb is loose or the connection between the bulb socket and a wire is loose. To check both, Loosen the screw knob on the underside of microscope and open the panel to expose the bulb. Use a small screwdriver to loosen the screws holding (the two screws closest to the bulb) the prongs of the halogen bulb. Note that the prongs of the bulb are held in place by small brass plates which shift slightly when the screws are loosened. Remove the old bulb. Important: Do not touch the new halogen bulb with bare hands. Wear gloves or hold the bulb using tissue or lens paper. Body oils may damage the halogen bulb. Insert prongs of replacement bulb into top of socket (above the brass plate) and tighten screws slightly. (The brass plates will move up to hold the prongs in place.) Close door and hand tighten the thumbscrew knob. If this does not work, contact Premier for assistance: Premiere® Microscope Service, 7241 Gabe Court, Manassas, VA 20109 (703) 330-1413

The error E61 indicates that your water pump has failed or is not active. You should check the pump and replace it if needed. You should also check the steam generator sensor and replace it if needed. For more information, contact Euronda at Water inlet pump inactive or call (+39) 0445 329811 (Vicenza, Italy)

If this is a microscope, the part you are referring to is the stage control. You can get the part from C&A Scientific at http://www.cnascientific.com or by calling 703.330.1413

Troubleshooting Microscope Lighting

DIGITAL MICROSCOPEOne device for measurement and quality control Please see above