Top 20 Canon imageRUNNER C3200 Copier Questions & Answers

Question edited for clarity, add maker and model series. Question moved to correct category.

Error Code e000733-0000 on Canon iR-ADV C2230

Copytechnet https://www.copytechnet.com > ... > Canon Nov 26, 2020 - Check the connection of the Flexible Cable between the DC Controller PCB (UN9) and the Main Controller PCB2. -- removed and re-connected ribbon ... Thread: Canon IR3245 E733-0010 & E197-0001 error codes Jul 26, 2014 ir5075 E733-0010 - Copytechnet Jul 14, 2011 Error Code CANON IR ADV 4035i E-733-0010 - Copytechnet Dec 19, 2019 Canon IR3300 error code E000733-0001 - Copytechnet Oct 9, 2007 More results from www.copytechnet.com

It appears your machine suffered a power surge and must be reset. http://okb.oceusa.com/service/main.jsp;jsessionid=AD324B614CBFCAC0264A5C5AC20E3A60.node6?t=solutionTab&ft=searchTab&ps=solutionPanels&locale=en-us&_dyncharset=UTF-8&brand=oce&curResURL=%2Fservice%2Fmain.jsp%3Bjsessionid%3DAD324B614CBFCAC0264A5C5AC20E3A60.node6%3Ft%3DsearchTab%26_dyncharset%3DUTF-8%26brand%3Doce%26locale%3Den-us%26lstLanguageQuery%3Den-us%26lstLanguageResults%3Den-us%26sfield%3D%26dosearch%3Dtrue%26searchstring%3DHow%252520to%252520reset%252520error%252520code%252520C2204%26useFocusTopic%3Dtrue%26focusTopic%3D9000503&solutionId=20812&isSrch=Yes

The controller fan is faulty

Dear The error occurs in accessing to the counter memory PCB. Disconnect, clean and connect the counter memory PCB, or replace it. If problem persists replace the main controller PCB (Main). Thanks.

you need to buy that manual? or please especify the error in your machine

Possible Solution:The Black toner feed motor was wired incorrectly causing the motor to operate in reverse. Toner would be augered away from the opening instead of toward it. The part number for the toner cartridge drive assembly is FG6-8999-000.* The assembly is more cost effective than the motor.

Error code E000020-04a0 fixing unit problem,Change it.

Laser polygon mirror motor is in the laser assembly. Take off front and left cover on copier and remove laser gently out of left side. Laser scanner motor is behind the reader rear cover.

FIXING FILM PROBLEM

Those codes are usually related to a hardware failure in the machine, probably a specific color drum unit or possibly fixing section...prob going to need a service rep to help you on that one if a simple power cycle didn't clear the issue. If your tech savy I might be able to guide you through a code reset. Thanks

DOES IT HAVE A USB PORT THAT YOU CAN CONNECT A LAPTOP TO? If so download the appropriate software from their site and update using the laptop.

low power, pls check the input voltage

Check in service mode, * 2 & 8 *, under Copier > display > Dens. Look at the value for each individual color. The normal value would be between zero and one. If you have a color with a value around four or five you have an issue with the toner/starter concentration level for that color. By replacing that color drum unit you will temporarily resolve the issue due to the Developer Assembly being incorporated with the drum unit, which has the correct toner/starter concentration. To resolve this issue replace the Toner Cartridge Drive Assembly, FG6-8999-000, and the corresponding drum unit at the same time.

that procedure is complicated, you should refer to the service manual for appropriate procedure

remove the cover on the top of the waste container and clean all the sensors thet related to all dv units

coz of low power, check your input power first

Is it just when printing that the screen goes blank? Does the machine function ok when copying? Does it shut down the machine when printing to it? If you could provide a few more details I can most likely help you with your issue. Thanks

The stapler shift motor (M4) or the stapler shift home position sensor (PI7) is faulty. There is a fault in the path of the stapler

maybe there is a dots on drum, and also check the primary corona assy