20 Most Recent
Canon imageRUNNER C3200 Copier - Page 6 Questions & Answers
X64 w7 driver
Why don't you look at the Canon website for the drivers you need. It isn't the most obvious place to look I know, but worth a try (don't you think?)
10/10/2013 3:09:48 PM •
Canon...
•
Answered
on Oct 10, 2013
Change ir2200 display language
Do you need to change it to something else for someone? Or did someone decide to play games with it and change it to something you can't understand? You're probably best off accessing the printer through the web interface panel rather than through the control panel on the printer. It does have a reset defaults in there.
10/4/2013 4:56:49 AM •
Canon...
•
Answered
on Oct 04, 2013
Error E 732 0001
E732-0001 Error Code: Reader Controller PCB is faulty[ Case in the field ]DescriptionE732-0001 can be displayed when a communication error occurs.CauseIn the field, this symptom occurred because the Reader Controller PCB was faulty.Field Remedy1. Make sure that the connector between the host machine and the reader unit is securely fitted.2. Make sure that the connectors on the Reader Controller PCB are securely fitted or there is no pinched cables.3. Remove and insert the Main Controller PCB (Sub) from the Main Controller PCB (Main). If the symptom still recurs, go to the Step 4.4. Replace the Reader Controller PCB with a new one.E732-0001 Error Code: locks up during copyingE732-0001 can be displayed when a reader communication error occurs.CauseAs a result of inspection, it was found that this symptom occurred because of poor soldering of J1302-34pin on the Main Controller PCB (Sub).Field Remedy1. Make sure that the connectors are securely fitted between J1302 on the Main Controller PCB (Sub) and J502 on the Reader Controller PCB and thatthere is no pinched cable.2. If no problem is found, replace the Main Controller PCB (Sub) with a new one.E732-0001 Error Code: Because of poor contact of SDRAMDescriptionE732-0001 indicates that a reader communication error has occurred.Field RemedyAs a result of inspection, it was found that this symptom occurred because the SDRAM was not securely fitted on the Main Controller PCB. So, removeand insert the SDRAM once again.
9/26/2013 1:31:09 PM •
Canon...
•
Answered
on Sep 26, 2013
Canonir3100cn error code E000020-0081
Hi,Dirty Drum patch sensor OR the drum has reached 100% of it's life.iRC3100 drums NEVER go past 100%...once they reach that magic figure in the counters then it's time for a drum replacement.If you know how to access service mode then check under:COPIER>DENS>P-SENS-P and make sure that the figure is around the 500 mark...if it's below say,250 then that indicates that the drum patch sensor is having trouble reading correctly and may either need cleaning or a new drum unit.If more help also see this link:
http://www.fixya.com/support/t575849-re_canon_ir3100cn_e000020_0081
9/25/2013 3:14:56 PM •
Canon...
•
Answered
on Sep 25, 2013
E000024 0001
E024-0001 Error Code: Toner gets in the developing assembly toner sensor (TS1) and may be shorting out the sensor. Blow out any toner in the sensor wiring and check to see if measure resolved the symptom. The toner level sensor has an open-circuit, replace the toner sensor. Toner Sensor FK2-0358 However, re-attachment of the sensor also solves the symptom.When the symptom has occurred, make the following selections in service mode [COPIER > I/O > DC-CON] and check the setting for the bit1 of [P021]. If the setting is "1", re-attach the toner sensor.I sugest getting the service manual it will help you and u will save money, you can download it from the below link:
http://goo.gl/RLoJzCgood luck
9/13/2013 4:16:52 PM •
Canon...
•
Answered
on Sep 13, 2013
Not finding what you are looking for?