20 Most Recent JVC HD-52Z575 52" Rear Projection HDTV-Ready Television - Page 3 Questions & Answers


Are you getting any lights at all on the front. Check and replace lamp.

JVC HD-52Z575... | Answered on Nov 24, 2009


it has automatic signal detection,just like a computer with windows xp. if you plug in a jack,it tells you

JVC HD-52Z575... | Answered on Oct 03, 2009


sounds like a covergence problem, cost 350 to 450

JVC HD-52Z575... | Answered on Aug 27, 2009


If you swapped directv receivers and the problem followed to a different tv then there is something wrong with the directv receiver. Need to run satellite setup again on this receiver to fix. repeat satellite setup is accessible through the setup submenu by pressing menu from the directv remote. look under satellite submenu once in setup

JVC HD-52Z575... | Answered on Aug 02, 2009


THE 1'ST CHEAPEST THING TO TRY IS FIND A STRONG MAGNET AND PUT A THIN PIECE OF CLOTH OVER IT, PUT IT AGAINST THE SCREEN AND SLOWLY GO OVER IT WITH A LEFT 2 RITE THENUP AND DOWN IF THIS WORKS IT WILL ONLY GET YOU BY FOR A WHILE.HOPE THIS HELPS.

JVC HD-52Z575... | Answered on Jun 09, 2009


hello i have a jvc 52" made in july 2004 replaced bulb twice under warranty plus replaced ballast board in 2005 replaced bulb dec 2008 my tv was before and after install having a blue hue reversed words

JVC HD-52Z575... | Answered on Jan 12, 2009


Look in the owners manual for the directions on how to remove the lamp. Your model the lamp goes in from the front on the left looking at the TV. There is a thumb screw in the back on the corner holding the left front speaker on. Under the panel there is another thumb screw holding the lamp door on. You will need a Phillips screw driver to remove the lamp. You will most likely find that the lamp is bad. You will either have to order a lamp directly from JVC, a service center or a parts distributor.

JVC HD-52Z575... | Answered on Sep 28, 2008


Will you will have to replace it now because this is the most likely cause for the blinking lights. Look in the instruction book for the directions on how to remove the lamp. You will find that it has burned out. It is easy to replace. You can order one from JVC or a service center, or a parts distributor.

JVC HD-52Z575... | Answered on Sep 25, 2008


You will need to have a service center come out to try to reset the TV using the reset jig. A JVC authorized service center will be the only ones that will have access to and training to use this jig. It is a good chance reseting it fix the color problem but it could also be something more serious.

JVC HD-52Z575... | Answered on May 11, 2008


The lamp is turned on by a high voltage ballast, very similar to the ones in your fluorsecent light fixtures. Your ballast is starting to fail. You should have your TV serviced by a JVC authorized service center because they have the training to deal with this issue. Waiting until it fails could very likely cause more servere damage especially if it fails shorted then the power supply will need to be replaced as well.

JVC HD-52Z575... | Answered on May 11, 2008


You both need to have a service center come out and reset the TV using the reset jig. This will correct the reverse image problem.

JVC HD-52Z575... | Answered on May 11, 2008


The green screen you read about is a solid color only when you select digital input. If you are getting green lines in any other input the reset will have no affect at all.
You will need to have the TV serviced, there is a possibility that the service center can use the reset jig to correct this. But it could be more serious.

JVC HD-52Z575... | Answered on May 11, 2008


Your HD-52Z575 will only be able to display an NTSC signal, PAL is not compatable. There is nothing that can be done to make it play a PAL signal.

JVC HD-52Z575... | Answered on May 11, 2008


It means the counter hours have been reached... Is it possible that you've had the lamp replaced once before and didn't reset the counter??
Bill

JVC HD-52Z575... | Answered on May 01, 2008


If the S-video cable is not completely in it will do this. You need to remove and clean tips on S-video cable/ replace, this is your problem.

JVC HD-52Z575... | Answered on Mar 10, 2008


On your blue tube there is a crt broad that may have a bad capacitor 4.7uf 250 volts most likely it can be leaky not able to hold correct charge also it might have video ic on same broard breaking down, this will cause your problem unplug crt broad from bottom neck of tube turn set on see if problem goes away if so then it means you have problem with crt broad or it could be your tube.Hope this helps you out!

JVC HD-52Z575... | Answered on Jan 18, 2008


PAL chroma operates at 4.43 mhz and NTSC operates at 3.58 mhz. Here is a link to PAL to NTSC convertors.

http://www.world-import.com/samar.htm

JVC HD-52Z575... | Answered on Jan 01, 2008


unplug and wait an hour and replug in.

JVC HD-52Z575... | Answered on Dec 05, 2007


You should have a button or setting on the remote that says "picture size" or "aspect". One of those is set too "zoom" mode which will cut off the bottom and top of the frames. You want it to be in 16:9,Normal or Full mode (or whatever your set call it) to get the correct aspect. Or if you have a HD satellite rcvr. you might of placed it in the zoom mode as well.

JVC HD-52Z575... | Answered on Apr 26, 2007

Not finding what you are looking for?
JVC HD-52Z575 52" Rear Projection HDTV-Ready Television Logo

74 questions posted

Ask a Question

Usually answered in minutes!

Top JVC Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76173 Answers

Todd Hill
Todd Hill

Level 2 Expert

433 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Are you a JVC Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

JVC Televison & Video

  • JVC Televison & Video

Most Popular Question

i2c stop accidentally entered in service

  • Televison & Video
Loading...