20 Most Recent JVC AV-32260 32" TV - Page 2 Questions & Answers

0060 0026 0197 0069 0247 0923 0012 0065 0067 0141

in menu look for closed captions---TEXT is engaged---if using a box it can also cause this. Switch text feature off,

Hello,

The issue you describe is consistent with a power supply board issue. This is the board where the AC goes to. This problem may have occurred as a result of irregular power supply, or excess power supply or power surge.

The TV is receiving current but cannot circulate or transfer the current to other necessary part of the TV because of the defective power supply board.

I do not think it needs replacement, rather some defective capacitors are causing this issue.
Open unit up and take a look at the power supply board.You will probably see one or more electrolytic filter capacitors that are bulged up in the top-not perfectly flat like the others.

The value of these capacitors will be different, most likely they will be somewhere around-820 to 2200uF/25 V( or /10V sometimes)

You can replace them with same values but I would recommend the voltage rating to be higher(like 35V for an original 25V) for reliability purposes.

What happens is,these bulged top capacitors will cause a low and unfiltered DC voltage=main board will malfunction(the relay will keep clicking until the caps are holding enough charge to bring the voltage up over a threshold point).

You can buy these capacitors at any Fry's or Radioshack store or you can order them online at vendors like "mcmelectronics.com"(look for electrolytic capacitors).
After replacing these capacitor(capacitors) most likely the normal operation will be restored.

Note: There may be also some other causes for this symptom ,like a defective T con board ,or main board,but the bulged top capacitors are the most common cause for this issue.

If you don't know about TV repairers, take the TV to the nearest repairman to fix the fault for you. Also, note that TV stores a lot of current, so wait a while before opening the TV back cover.

I hope this helps.....

Good luck.

I had a similar problem.. What's needed is to change the audio mode of the tv.
You may need the original tv remote to access it's setup menu or maybe able to do it with onboard buttons. (not the channel setup, but the screen brightness and hue and other stuff - Audio setup)

When entering the audio setup, you may find you're in surround sound or some other "type" of sound processing. Maybe simple Speech mode will suit you. Try different modes till you find a happy medium for your own taste.

You could go to the back of the cable box and change channel from 3 to 4 and use tv on channel 4

Wow that's interesting, was there anybody watching your home while you were gone? There is a possibility that someone simply turned down the color level with the color control? Check that first. It's an unusual symptom. With composite video, component video or HDMI it's not usually possible to experience that defect. Since the color (chrominance signal) is usually inseparable from the luminance (black and white signal) I would check the color setting first. Other wise your set has become unable to detect that color signal... I bet it's a setting rather than a defect.

Happy Viewing
Zashiban

Look through the menus (on screen) for the Closed Captioning (CC) and turn it (select) off.

If I remember correctly on these older CRT JVC sets. It was either press the "display" button on the remote a few times to turn the clock off or the option to leave it on is in the menu system.

We love shows like all the Law and Order shows and cannot hear the dialogue because of dreary useless background dirges. It is infuriating. Please stop it

Hello, I was the one who assisted you in Live Chat, Just wanted to remind you to rate the chat session, Thanks. Have a great day!

HERE IS SOME CODES FOR THAT TV 557 558 559 560

I had accidentally hit the text button and turned it on while trying to adjust the color. I turned it off with the remote and the problem went away.

it will work

yea ... i have one. I'll sell for $129.95. [email protected]

have had cases where electrolytic capacitors dry up and cause no start. set should be checked by a technition; get estimate on repair before throwing set.

Good day.

There might be some leakage along the regulator section of your unit. try to check for the leakages along the filer capacitors likewise.


Regards,


chris

Good day.

Can you please be more specific with the purpose of your capacitor and for which purpose is it?


Chris