Top 20
Braun Paxiscope XL Opaque Projector - 100522 Projector Lamp - Page 8 Questions & Answers
I have an error code 033001 on my xp-345
The error code 033001 on an Epson XP-345 printer typically indicates a communication error between the printer and the computer. Here are a few steps you can try to resolve this issue:
- Check the USB cable connection: Make sure the USB cable is securely connected to both the printer and the computer. If the cable is damaged or frayed, replace it.
- Restart the printer and the computer: Turn off both the printer and the computer, wait for a few seconds, and then turn them back on.
- Update the printer driver: Go to the Epson website and download the latest driver for the XP-345 printer. Install the driver on your computer and see if the error code 033001 has been resolved.
- Uninstall and reinstall the printer: Remove the printer from the Devices and Printers list and then reinstall it.
If the above steps don't resolve the error code 033001, you may need to contact Epson support for further assistance.
How to find MAD on an fx-9750GII calculator
You can use the built-in MAD function on the calculator by following these steps:
- Press the "STAT" key and then select "5:Distribution". Choose "1:Statistical Calculations" and then "4:Other".
- Select "4:MAD" and then enter your data set.
- Press "EXE" to calculate the MAD.
I have a problem with Riso SF5030, it shows error code P98-1061/ T98-1061. What maybe the problem
Hi!
Error codes P98-1061 and T98-1061 on the Riso SF5030 indicate an issue with the color drum's motor. This error code usually occurs when there is a problem with the motor or the wiring that connects the motor to the printer's control board.
Here are some steps you can take to troubleshoot the issue:
- Turn off the printer and unplug it from the power source.
- Check the wiring connections between the motor and the control board. Make sure that they are secure and not damaged.
- Check the motor for any physical damage or signs of wear and tear.
- If you have a replacement motor, try replacing the faulty one and see if the error code persists.
- If the issue persists, you may need to contact a service technician to diagnose and repair the problem.
It's essential to note that opening up the printer's internal components can be dangerous, and you should only attempt these steps if you feel comfortable doing so. If you are unsure or uncomfortable, it's best to contact a qualified service technician for assistance.
Regards
What size staples do I need for the Rapid Isaberg 16 stapler [prob 40/50 years old but still works superbly]
The Rapid Isaberg 16 stapler uses 26/6 size staples. These staples are also commonly referred to as "standard staples" and are widely available at most office supply stores or online retailers. They measure approximately 6mm wide and 11mm in length, and are compatible with a wide range of staplers, including the Rapid Isaberg 16. Be sure to use high-quality staples to ensure that your stapler functions properly and staples securely.
My 3d prints are stringing, even with retraction, why?
Stringing can happen if you print too hot, but if you use a slower print speed, you can usually get away with using a lower temperature. If you think incorrect temperature might be causing your stringing, the suggestion is to drop your temperatures by about 10°C and slow your print down slightly. Dry your filament.
How to change empty tray message please?
Question edited for typos.
All questions need full 'make model (what it is)' as the first 3 words.
Remove the tray and look for sensors or something on the paper tray that registers when it is out of paper. Fill the tray and replace it.
Also try a power reset. Remove to wall plug for 10 minutes then plug it back in.
..
Shredder Essentials SES-C1525 Shredder. How do I unjam a ses-c1525 jammed with what I think is sticky gunk.
Question edited for full 'make model (what it is)'.
People don't realize that shredders need oiling regularly. Spray all the blades and the gunk with WD40. Leave it half an hour and spray it again. Run it in reverse to clear the jam. If you have been using it a lot, they have a thermal cut out which should reset after about 20 minutes or so. Bad jams and heat, shatter and shred the gears inside the head. Is the motor making any noise?
TMX15 ERROR CODE 204 is coming up on display. Anybody know what that may be?
TMX15 is a model of a forklift truck, and ERROR CODE 204 indicates a fault with the accelerator pedal position sensor. This sensor is responsible for sending signals to the forklift's engine management system to control the speed of the vehicle.
The error code may have been triggered by a faulty sensor, damaged wiring or connectors, or a malfunction in the engine management system itself. It is recommended to have a certified forklift technician inspect and diagnose the issue to determine the root cause and necessary repairs.
It is important to address this issue promptly, as a malfunctioning accelerator pedal position sensor can affect the performance and safety of the forklift.
Can I put an equals sign on my calculator
Yes, almost all calculators have an equals sign. The equals sign is typically used to indicate the end of an arithmetic operation and to display the result. The location of the equals sign may vary depending on the specific calculator model, but it is usually labeled with the symbol "=" and located in a prominent position on the calculator keypad.
Cl-100 topcon lenso meter initial error problem always comeback when I fix.. pls help how to solve for this
The CL-100 Topcon Lenso meter is a surveying instrument used for measuring distances and angles. An "Initial Error" message can indicate a number of different issues, including:
- Calibration Issues: Check that the instrument has been calibrated properly and the calibration values are within the acceptable range.
- Software Issues: Update the software on the instrument to the latest version, which may resolve any bugs causing the error.
- Hardware Issues: Check the instrument's hardware components, such as the battery, for any signs of damage or wear and replace if necessary.
- Settings Issues: Make sure that the instrument's settings are set correctly and adjust them if needed.
- Environmental Factors: Environmental factors, such as temperature and humidity, can affect the performance of the instrument. Make sure that the instrument is being used within the recommended temperature and humidity range.
If the "Initial Error" message continues to persist, it is recommended that you seek assistance from a qualified Topcon technician or authorized service center. They can diagnose and repair the issue and restore the instrument to full functionality.
Caster holder broken and won't auto-stop after shred
I see you posted two questions on the same issue, and the other one was disjointed with no indication what the caster wheels were on.
Check the switch, they normally have On, Off and Auto.
Remove the head and clean all paper debris from underneath. You have a small piece of paper over the sensor and it is sensing that there is still paper for be shredded. Some have a small lever and if so, yours is stuck. Spray with WD40, and all the blades as well.
https://www.google.com/search?q=Ativa+MDM+8000
The caster wheels could all be removed and have it sitting on its base. The wheels are for use if you keep it in an office cupboard. You just replace the whole caster wheel or the whole set for $14..
https://www.google.com/search?q=Caster+wheel
..
Not finding what you are looking for?