Top 20
Braun Paxiscope XL Opaque Projector - 100522 Projector Lamp - Page 7 Questions & Answers
5700 stapler handle will not go down when pressed no staples in gun i removed the bolt and nut then the slide handle still doesn't move
If the handle of your 5700 stapler does not go down when pressed, even after removing the bolt and nut and the slide handle, it suggests there may be an issue with the internal mechanism. Here are a few steps you can take to troubleshoot the problem:
Check for jammed staples: Even if there are no staples visible in the stapler, it's possible that a staple may be jammed inside the stapling mechanism. Try using a pair of tweezers or small pliers to carefully inspect and remove any debris or jammed staples that may be obstructing the movement of the handle.
Lubricate the stapler mechanism: Apply a small amount of lubricating oil or silicone spray to the moving parts of the stapler mechanism. This can help loosen any stuck components and improve the smoothness of the handle's movement. Be sure to use a lubricant suitable for mechanical devices.
Clean the stapler: If the stapler has been used in dusty or dirty conditions, debris may have accumulated inside, affecting its operation. Use compressed air or a soft brush to remove any dirt or debris that may be hindering the movement of the handle.
Inspect for broken or worn parts: Carefully examine the internal components of the stapler, such as springs, levers, and pins, for any signs of damage, breakage, or excessive wear. If you notice any broken or worn parts, it may be necessary to replace them to restore the stapler's functionality.
My 2253lw monitor samsung, is it full white
There is a hardware problem here or the graphics card driver is not able to work properly.You will need to update or reinstall your drivers in Windows safe mode to fix this problem.
How to fix Riso cv 3230with error code p 01 -537
To fix the error code P 01 -537 on a Riso CV 3230, you will need to reset the machine. To reset the machine, press and hold the Stop/Reset button for at least five seconds. This will reset the machine and clear the error. If this does not work, then you may need to perform a deep reset of the machine. To perform a deep reset, unplug the machine from the power source and then plug it back in. Allow the machine to go through its startup sequence and then test the machine again.
How do you fix error code 53 (holding brake slipping) on pre or e-fax 5.17?
Error code 53 on a Pre or E-Fax 5.17 typically indicates a holding brake slipping issue. Here are some general steps you can take to troubleshoot and potentially fix the problem:
- Power off the device: Turn off the Pre or E-Fax 5.17 and unplug it from the power source. This ensures your safety while working on the device.
- Check the holding brake mechanism: The holding brake is responsible for preventing the machine from moving when it is not in use. Inspect the holding brake mechanism for any signs of damage or misalignment. Ensure that all components are in their proper positions and are functioning correctly.
- Clean the holding brake: Dust, debris, or dirt accumulation can cause the holding brake to slip. Use a clean, dry cloth or compressed air to carefully remove any dirt or debris from the holding brake mechanism. Be gentle to avoid causing any further damage.
- Adjust the holding brake tension: If the holding brake is not gripping adequately, it may require an adjustment to increase the tension. Consult the user manual or documentation for your specific Pre or E-Fax 5.17 device to determine the proper method for adjusting the holding brake tension. This process may involve tightening or loosening specific components of the brake mechanism.
- Test the holding brake: After cleaning and adjusting the holding brake, reconnect the power and turn on the device. Test the machine to see if the holding brake is gripping properly and preventing unwanted movement. If the error code 53 no longer appears and the holding brake functions as expected, the issue may be resolved.
- Contact technical support: If the error code persists or if you are unsure about performing any troubleshooting steps, it is advisable to contact technical support for assistance. They can provide specific guidance for your Pre or E-Fax 5.17 device and may be able to offer further troubleshooting or arrange for repairs if necessary.
My seca 813 only showing STEP OFF AND STOP massage cannot reset ??
If your Seca 813 is only showing the "STEP OFF" and "STOP" messages and is not responding to any commands, it is possible that there is a problem with the scale's sensors or the internal circuitry. Here are some steps you can take to troubleshoot the issue:
- Make sure that the scale is on a flat and stable surface. If the scale is on an uneven surface or is wobbling, it may not be able to take accurate readings and could display error messages.
- Check the scale's batteries. If the batteries are low, this could cause the scale to malfunction. Replace the batteries with fresh ones and try turning the scale on again.
- Reset the scale. Some scales have a reset button or function that can be used to clear any errors or malfunctions. Refer to the user manual for instructions on how to reset your specific model of scale.
- Check the scale's sensors. Over time, the sensors on a scale can become dirty or worn, which can affect their accuracy. Clean the sensors with a soft cloth or brush and see if this resolves the issue.
- If none of the above steps work, you may need to contact Seca support or a professional technician for further assistance. They may be able to diagnose the issue and recommend a repair or replacement if necessary.
Emerson coin sorter will not turn on. Need manual please
Greetings,
Please reach out to your local home hardware store over the phone to request the manual from them. Tey might also be able to request the manual from an Emerson representative for you. And it would be your choice to pickup the manual at the store or have it mailed to you.
Thank you.
How to remove FRAC display on porpo YH-2000 calculator
To remove the fraction display on a Porpo YH-2000 calculator, you can follow these steps:
- Press the "Mode" button to access the calculator's settings.
- Use the arrow keys to navigate to the "Fraction" or "Frac" setting.
- Change the setting from "On" to "Off". This will remove the fraction display from the calculator's screen.
- Press the "Mode" button again to save the changes and exit the settings menu.
If these steps do not work, it's possible that your calculator model is different or that it has a different method of changing the fraction display. In this case, you may want to consult the manual or manufacturer's website for more information.
Error code 652 , Q500 TGA
Are you referring to TA Instruments Thermogravimetric Analalyzer? That's not exactly what I think of as office equipment. https://imri.uci.edu/facilities/tempr/tempr-instruments/q500/ I suspect your company has a service plan for this equipment. The instrument's company's support site is https://www.tainstruments.com/support/ You might try the followin forum: https://www.labwrench.com/thread/242221/error-192 I don't see the error codes listed: https://www.manualslib.com/manual/1246529/Ta-Q-Series.html?# Sorry.
MEMBERS'S MARK MICRO CUT/12 PULSES WHEN SHRERRING. WORKS GOOD IN REVERSE
If your Member's Mark micro cut shredder is experiencing a problem where it is making 12 pulses when shredding and works good in reverse, it is possible that there is an issue with the shredder's motor or transmission. Here are a few things you can try to troubleshoot the problem:
- Check the shredder's capacity: Make sure the shredder is not overloaded and that you are using it within its capacity. Overloading the shredder can cause issues with the motor and transmission.
- Check for debris: Look for any debris that may be stuck in the shredder's mechanism. Debris can interfere with the movement of the shredder's components and cause problems.
- Check for other issues: If the shredder is not overloaded and there is no visible debris, it is possible that there is another issue causing the problem. You may need to have the shredder serviced by a professional to diagnose and fix the issue.
I hope this information is helpful. If you have any further questions or need additional assistance, please don't hesitate to ask.
Riso ComColor 7050 Error 0B31 - what do I do?
The 0B31 error code typically indicates that the cooling fan is not working correctly and needs to be replaced. Try to reset the fan and ensure the cables are securely connected. If that does not resolve the issue, the fan may need to be replaced.
Milnor commercial washer model # 30022T5X
The Milnor 30022T5X0 is a commercial washer that features a high-speed extraction system, low water usage, and a convenient front-load design. It offers a capacity of up to 25 pounds and can handle a variety of fabrics, including towels, sheets, and uniforms. The 30022T5X0 also features an energy-efficient design and an adjustable water temperature for better cleaning results.
Not finding what you are looking for?