20 Most Recent NetGear WNDR3400 N600 Wireless Dual Band Router (WNDR3400100NAS) - Page 3 Questions & Answers

your pc problems have nothing to do with your new router. Your pc sounds like the mobo is not sending a kill signal to the power supply. You can either re-flash you mobo bios or try a patch for windows. Most likely this is not a fixable problem as the cost to fix it will be as high as a new pc.

What lights are "on" on the router - what happens exactly when you do the reset - do the lights change at all leave the unit unplugged for 30minutes - reconnect - does it now work is it running hot at all ?

Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults. However, once the device is reset to factory defaults, you can use the default username ("admin") and password (either "password" or "1234" depending on your router) to reconfigure your router settings. if there is a small hole in the front or back of the router push a hair pin in to reset to factory settings
Hope this helps don't forget to vote

Original installation disk should have master reset option.

Check with your service provider. You may be in a fringe area or receiving a poor signal because of interference. If your router has the option to add an external antenna that may solve your problem.

Double check your password.

Sounds like the power supply is unp

Step 1 hey can you login to your router of yes make sure your router is dhcp enabled, then on you phone kindly delete or forget your current wifi settings, then do a phone restart and register a wifi (connect to a new wifi spot) and try again. Step 2

1. If the page displays, you have Internet access. If the page does not display in a minute, see the "No Internet With New Router, Computer or Adapter: MAC Spoofing" article.
2. Determine if the modem's IP address can be seen. In the router interface, go to the Status Page. For more information, see your router user manual. If the modem's IP address cannot be seen, reboot the modem, router, and computer, in that order. Be sure to wait for each device to completely reboot before rebooting the next. If the modem's IP address is seen, and you stuill cannot access the Internet, you might have a problem with your browser's settings. Your security might be set too high for the Internet service you are trying to use, or your browser might be configured for a dial-up connection. In Internet Explorer you check this using Tools > Internet Options > Security > Default Level. If the slider is set to High, change it to Medium. Click Tools > Internet Options > Connections. If the radio buttons in the center are not dimmed, settings for a dial-up connection are being used.

Hello, Your wireless router is to blame for this one. You need to raise it up as high as you possibly can, and also it needs to be placed in a spot with the least amount of interference or signal blockers in the way such as walls, ceilings, and floors between it and the wireless products requiring it to function! Another possibility is to add to the network another "ACCESS POINT" or wired to wireless router at the highest possible point if you cannot move the 1st router. A totally wireless router will work but it has to have a strong wireless signal (from the 1st router) to work properly. Good Luck! Rich Lilja

Try reducing the TXqueue length. Try a number like 200.

5 ghz is line of sight only so if the router is not in the same room you will not have much luck with the 5ghz band.

Have you tried changing the channel the router is broadcasting on? sometimes if a neighbour is using the same chanel you can get conflicts. Take it of Auto and choose something like 9,11,12

The wireless router has capacity to over perform only situation with the device connectoins to your computer are receiving signals from more than one network. You are allowing several signals to access the computer. Establish one network pass at a time. a stronger once should be chosen and the device would perfrom to capacity. The network setup need to be reconfigured

you might try moving your computer closer to your router
make sure your routers and your dell 1450 settings are correct ie:password user name,firewall settings to allow your internet to connect also test the lead/s whether usb or ethernet if applicable

hope this helps

Never buy Netgear. They design product so it won't work unless you pay more for technical support. They told me the technicians during the 90 day warranty are not good enough to fix problems, so you can't get solution until warranty runs out and you have to pay extra!

There is a great article at Working with Windows Wireless Networks
If you need more help post back! Thumbs and testimonial are welcome!

to test your connection, launch a web browser and and enter http:192.168.0.1 or http:192.168.1.1 in the address bar or look for a small hole at the back of the router and use a pin to reset it by pressing it in through the hole when it is on until it restarts it self the try connecting

typically your router should pick that up automagically from your ISP. If the power failure reset your router to factory (unlikely) you will need to login to it and reset those settings. from a computer connected to that router run a dos console (type cmd in win 7 or 8 start menu or xp run menu) then run ipconfig, write down the gateway address and use internet explorer to browse to that address (type the address in the address bar). login to the router and look for the ISP settings and such. your ISP should be able to help with those settings. that failing use 8.8.8.8 (google) as a DNS server in your computer IP configuration.

This router does not use any type of PIN. You may be confused as the HP wireless networking setup may be asking for the "password", or WPA2 key that secures the wireless network. This must be entered before the router will accept the client and assign it a network IP address. The WPA2 key is stored in the router under the Wireless Settings Option. Unfortunately, if you don't know the key, going there won't help you as the key is not visible.

Had same problem - said signal weak although strong on other devices, and hung on authenticating.

Cordless phone on base unit was beside wireless router. Moved unit and turned off phone. Problem disappeared, and signal showed strong.