SYMA Toys industrial New Syma S107 Radio Remote Control Helicopter - Answered Questions & Fixed issues
My syma s107g gives a
fully charge your heli----turn on transmitter-wait 2 seconds-turn on heli
wait for blinking green led to stop blinking-turns steady.....rev up
with a quick full throttle and back to idle--happy flying
3/14/2019 2:11:06 AM •
SYMA Toys...
•
Answered
on Mar 14, 2019
•
2,581 views
My S107g wont respond to the transmitter
I have the same problem, worked twice with a steady red light but then back to flashing and no comms. Turned all the TV's and wireless network off to see if this would help but still no joy. Need a solution as these are really cool little toys !
1/21/2015 6:32:34 AM •
SYMA Toys...
•
Answered
on Jan 21, 2015
•
748 views
Do the helicopter itself have a on/off switch..tech-one gallant
After fights between teh kids (he's crashing my helicopter) I think I figured it out. The instructions says to select the frequency on the helicopter, but there is no switch. When you first bring up the helicopter and controller, sometimes the green light on the controller blinks a few times. That is it synching up with the helicopter. After you charge the helicopters, turn then both off, Then turn on one helicopter and one controller. The key is when the green light above the one off switch is blinking. I did it with trial and error, so I am not sure exactly how to get it in the mode where it is in pairing mode. RIght now I am reluctant to mess around with it because they are set correctly and the kids are playing with them. I will post later if I figure out the exact sequence for getting them in pairing mode
1/21/2015 6:30:01 AM •
SYMA Toys...
•
Answered
on Jan 21, 2015
•
427 views
How to fix a syma helicopter if it is not responding
My helicopter used to do that too I called the company and told them my problem they said to change the batteries in the helicopter in a week they delivered the batteries and my helicopter was working agaim
8/20/2018 8:49:45 PM •
SYMA Toys...
•
Answered
on Aug 20, 2018
•
714 views
Everything spins including the body
Hi,
Sounds like one of the motors is not working it has either burnt out or the drive cog is slipping or come off.
Kind regards, Julian.
rccontrolfreak.co.uk
1/31/2014 1:38:45 PM •
SYMA Toys...
•
Answered
on Jan 31, 2014
•
54 views
I have 3 s107 and
Mine's exactly the same as yours. Although the transmitter shows A B C the switch has only two positions, so there's a choice of two only. I doubt it's possible to fly 3 at the same time.
12/27/2013 6:06:37 PM •
SYMA Toys...
•
Answered
on Dec 27, 2013
•
3,254 views
I have a s033g helicopter with about 20 flights on
Have you checked that the main gears are not slipping as it only takes the drive on one set of blades to slip and you will not have enough powere to take off even though it seems both sets of rotors are spinning.
Kind regards, Julian
rccontrolfreak.co.uk
12/3/2013 8:09:32 PM •
SYMA Toys...
•
Answered
on Dec 03, 2013
•
173 views
My S107 does not hover
The upper shaft 'T' head has a broken pin in it (the part that holds the blades. You can flip the heli upside down and slightly rotate the blade housing back and forth and IT SHOULDN'T do that. Another way to instantly identify it is dislocate the rotor head links and the upper blade housing should instantly separate) It's made of plastic.
Anyway, It's also called the "T.B.E." Toilet Bowl Effect. It's not 'really' what's taking place, it's move of a cyclic issue but the effect looks like it's swirling in a toilet bowl... You need to replace the inner shaft basically on the upper rotor. They cost anywhere from $4-7.00 bucks. It took me about 2 days of researching and purchasing another one to finally figure it out. There was another website that says the balance bar is it or the gyro has gone bad; this simply isn't true.
Cheers!
4/8/2013 9:45:22 PM •
SYMA Toys...
•
Answered
on Apr 08, 2013
•
7,772 views
My S107G is fully charged, I turn on and off transmitter on different frequencies, turn the heli on and off according to my instruction manuel, but the lights on the heli are on,the circuit board red
Hi,I have similar problem with my LS-208 heli.Helicopter leds are blinking red/green, front white led is on, and tail leds are blinking too.Remote controller red led is on as should be but helicopter doesn't respond to controller at all.I followed instructions above with no success.Anyone has a suggestion?Regards, Yaron.
3/19/2014 9:32:22 PM •
SYMA Toys...
•
Answered
on Mar 19, 2014
•
2,938 views
Helicopter not stable
Hi, I had a toilet bowl effect after changing the blades on my s107g. After making sure the shaft was seated properly, I simply adjusted the tension on the screws holding the blades in position and after a bit of trial and error tightening and loosening: it's as good as new!
1/24/2013 10:38:23 AM •
SYMA Toys...
•
Answered
on Jan 24, 2013
•
366 views
Not finding what you are looking for?