Keyless Entry Remote Fob Clicker for 2004 Malibu Memory 2 (Mus - Answered Questions & Fixed issues

The Chevrolet Malibu is among the many Chevy cars that come with remote and keyless entry. With this technology, you can control your car's door locks, your trunk and your panic alarm from as far as a couple hundred feet away in the street or in a parking lot. Programming will take you only minutes from your driver's seat, and you will have the remote and the system transmitter ready to use right away. 1 Enter your Malibu and close all the doors. 2 Insert your key into the ignition. Cycle the key to "On," then "Off." Remove the key from the ignition. 3 Press and hold the "Unlock" tab on the driver's side door as you insert and remove the key from the ignition three times. 4 Release the "Unlock" tab. Press and hold both the "Lock" and "Unlock" buttons on the remote until the car beeps twice. 5 Repeat Step 4 for any additional remotes. Remove your key from the ignition to end the programming sequence.

Test Procedure 1 Diagnostic System Check (requires scanner) 2 Transmitter Test (requires transmitter tester) Most times if lock/unlock works correctly from interior switches problem is transmitter. IT CAN BE TESTED with J 43241 Keyless Entry Tester. This is most times only found at larger GM dealerships. Take it into parts department and ask to be tested before replacement. BE SURE THEY HAVE THE TESTER. smaller dealerships very often do not. If it tests good, Diagnostic System Check is required.

If all rear lamps not working, unlikely all bulbs bad--more likely that you have lost ground(s)

Is it a factory installed system, if so there is no valet button.

There should be a key specifically for a valet.
1) Open one of your vehicle's doors and turn the ignition, using the car key, to the "Run" position. Check to see that the dome light comes on. Make sure that you have the dome light set to the position where it powers the light when the door is opened, as there are usually three settings: one for "On," one for "Off" and one for when a door is opened.
2) Press the valet remote push-button to access the channel that you want to program: once for "Arm/disarm," twice for "Trunk Release" and three times for "Remote Start." The valet push-button is usually located under the driver's side panel, and it must be pressed within 15 seconds of opening the door. The push-button may also be installed underneath the kick panel.
3) Press the valet push button once again and wait to hear a chirping or a honking sound. If you do not hear either of these sounds, your vehicle might have a jumper installed that has turned the valet programming feature off. Refer to your vehicle's instructional manual to learn how to set the valet programming feature to the "On" position. Keep holding the valet button pressed as you continue onto the next step.
4) Push the button on the remote that you wish to assign to a particular valet channel. Press the button on the hand-held valet remote that you wish to assign to a particular valet channel. If you wish to program multiple remotes, repeat this step for each of them. If you program four or more remotes, the old programming will be erased.
5) Let go of the valet push-button and exit your vehicle. Your handheld remote is now ready to use.
Tips & Warnings - Some valet remote channels require different programming individually, so refer to the owner's manual or to the link provided in the "Resources" section of this article, for specific instructions.
- Valet remote programming methods may vary, depending on the vehicle's make and model.

You need to get a new actuator. Check it with the switch inside to verify the mechanism. Usually this is an indication that the actuator is bad, especially when all the other ones function correctly.

The rear side door actuator control modules monitor the power sliding door positions at all times. Whenever the battery positive voltage supply to a rear side door actuator control module has been removed or the on-board diagnostics have been activated the power sliding door system(s) must be re-initialized. Re-initialize the right or left power sliding door systems using the following steps:

1. Turn the ON/OFF switch for the power sliding door system to be re-initialized to the OFF position.
2. Manually open the power sliding door completely.
3. Manually close and latch the power sliding door.
4. Turn the power sliding door ON/OFF switch to the ON position.
5. Open the power sliding door completely using the B-pillar or overhead console OPEN/CLOSE switch.
6. Close the power sliding door completely using the B-pillar or overhead console OPEN/CLOSE switch.

What is the question?

165 ft lbs

have truck scanned for a trouble code active or pending this will cause no start conditions

It is still immobilized through the alarm system then.

http://repairguide.autozone.com/znetrgs/repair_guide_content/en_us/images/0900c152/80/25/f9/97/large/0900c1528025f997.gif We Are Here To Help !!!

Yes. The inner door panel needs to be removed since the switch is on the inside of it.

The code is: P2000 NOx Trap Efficiency Below Threshold Bank1 and I do not know what that is unless it has something to do with the oxygen supply to the engine. Sorry I am not much help.

sounds like the alternator is not putting out. If you start the car and remove the battery cable and the engine shuts off then the alternator is bad and you need to change it.

take the screws out of the arm and take it down.

check everything else, I don't believe it has one

chevy aveo wiring diagram Google Search

1996 Camaro Z28 Wiring Google Search

it that on the door the heater the radio the steering column or on your Sony Walkman??