5303L 2Way LCD Remote Start Security System - Answered Questions & Fixed issues

I got this free Pdf manual fro m reliable-store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of the 20 times I fixed the chipper in these 4 yearsmust try this bitman and reliable-store. Both are good

I got this free Pdf manual from reliable-store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of all the times I fixed the chipper in these 4 years

all depending if your trunk work with negative ,or positive pulse if it is positive you have to used a 5 pin relay and if its negative just connect it straight

You can put the alarm in valet mode so it's inactive. There is a pushpurltron switch il under your dash all you need to do is turn the ignition on and within 10 seconds press that button once then turn off the ignition. Link to a owners manual http://www.manualslib.com/manual/13567/Avital-5303.html?page=21#manual

What is make of the remote starter? Look on the Internet for the instructions

is it an after market alarm? replace battery in remote!

It is caused from data interference by the bypass module. A different firmware will need to be used or a different bypass all together. If Frys recently installed it, then they should be responsible to fix under warranty.

How long do you want it to run? Thats normal go into setup if you want to change

you check to see if the engine was hot or something like if the water level in the radiator was down the sensors in the security system would pick it up

A security or transponder bypass.. there are a few different companies that make them.

Remote start the vehicle using the remote.

sounds like the brain is malfunctioning

https://www.google.com/search?q=AVITAL+REMOTE+HOW+TO+SET+TIME+FOR+CAR+RUNNING

To put your Avital 7345L remote starter on vibrate instead of chirping, you will need to follow these steps:

1. Press and hold the "Valet" button on the remote starter until the parking lights flash twice. This will put the remote starter into valet mode.
2. Press and hold the "Lock" button on the remote starter until the parking lights flash twice. This will turn off the chirping feature.
3. Press and hold the "Unlock" button on the remote starter until the parking lights flash twice. This will turn on the vibrate feature.
4. Press and hold the "Valet" button on the remote starter until the parking lights flash twice. This will exit valet mode and save your settings.
5. Test the remote starter to make sure that it is vibrating instead of chirping.

Note: If you have difficulty following these steps or if you have any other issues with your Avital 7345L remote starter, it is recommended that you consult the user manual or contact the manufacturer for assistance.

Wheel Bands get the best rim edge protectors

If you are looking to sync the remote key fob to the remote starter: Remote programming 1. Turn key to the ON position 2. Within 5 seconds, press and release Valet button one time. 3. Within 5 seconds, press and hold the Valet button. The LED will flash one time and the horn honks to confirm entry into remote programming. 4. Press the button on the remote control. 5. The horn honks to confirm the remote has been programmed. 6. Release the Valet button, and turn the key to the Off position. 7. The horn sounds one long honk to confirm that remote programming has been exited. The programming routine exits if any of the following occurs: • The ignition is turned off • There is no activity for 30 seconds • The Valet button is pressed too many times

sadly I never heard of that make here in usa

Yes, your antitheft system need resetting because you disconnected the battery. Because you have an aftermarket remote starter, get the installer to come out to you and reprogram everything. Number 1 tip. When changing a battery, always maintain a 12 volt supply during changeover using a battery tender, the existing battery with jump leads, or a special attachment that goes into the cigarette lighter.

Contact Avital directly to request the manual.

Get a meter and connect it at the battery terminal connectors while somebody starts the truck. Don't connect directly to the battery posts. If you get a big voltage drop, it might be the connectors not cleaned or tightened properly, or could be the battery. Many car alarms sound when the voltage isn't high enough. Also when you had the avital installed, they had to disconnect the battery, so it could be that.