20 Most Recent
Kettler TX1 Treadmill with FREE INSIDE Delivery! Treadmill - Page 8 Questions & Answers
Was goin to buy a second hand kettler traveller
Dear Sir:I recomend that you read your instruction manual carefully for warning, tips from the factory . If you do not have, please go the next web pages:www.fitness.manualsonline. com or www.iconservices. com for free download. sincerely. God bless you.ernesto cuadramanagua, nicaragua.
I need a training manual for a kettler apollo
Hi,
The Kettler Apollo Gravity System inversion table allows you to hang upside down. Inversion table proponents claim that the exercise machine aids in the relief of several ailments, most notably back pain. As with any exercise equipment, you must operate the Kettler Apollo Gravity System correctly to get the full benefit of the inversion table and to avoid injury.
- Pull the pin out of the Kettler Apollo frame next to the left arm and insert it into one of the six maximum inclination holes. Place the pin on the right side of the frame into the corresponding hole. The maximum inclination holes determine how far back the Kettler Apollo swings when leaning back. When pins are in the uppermost holes, the table will stop at a horizontal position. Each subsequent hole increases the backward inclination of the table. The sixth hole is the maximum inclination on the Kettler Apollo.
- Press down on the foot grip handle and move it forward to open the foot grip. Stand on the foot rest and rest your back against the table. Note the location of your head on the table. The top of your head should rest near the top of the table back without hanging over.
- Loosen the foot rest screw by hand and move the foot rest up to a higher hole if your head rests far below the top of the table or down if your head hangs over the table. Tighten the screw in the hole and check the placement of your head again until your body is in the correct position.
- Open the foot grip by the handle, stand on the Kettler Apollo and pull the foot grip handle toward your body. The foot grip keeps your body attached to the chair when you lean backward.
- Raise one of your arms slowly to change your body's center of gravity and start the table leaning backward. Lift your second arm into the air slowly if the table does not move after raising your first arm.
- Grip the left and right handles with your hands when leaning backward and pull up to change your center of gravity and return to the starting position.
Regards.
I have a kettler condor
I posted this for a few people, if this is about replacing the battery:If you look behind the unit, (directly behind the digital readout) you'll see a small rectangular inset, if you look up in that (I used my cell phone light), you'll see a tab that you can pry with a screwdriver gently to release the computer section. Just keep one hand on top, when you pry it you'll feel the unit pop up, then you can lift it out. It takes 2 AA batteries, thankfully not some bizarre disk batteries :)Btw when you look at the readout, you'll notice it's set in a silver square- that square is the computer module that pops out.Hope this helps!
I have a Kettler Condor Elliptical and when I use
Do you still have your manual? I kind of remember running into this, I think it was something simple( sorry I can't recall!) like lubrication or uneven alignment (fixed by adjusting the feet). I don't see the condor on the kettler USA site, but they still may be able to help.
I have a Kettler Elliptical. It is the Condor
Here's what I posted for someone else, I had to change my batteries this morning:If you look behind the unit, (directly behind the digital readout) you'll see a small rectangular inset, if you look up in that (I used my cell phone light), you'll see a tab that you can pry with a screwdriver gently to release the computer section. Just keep one hand on top, when you pry it you'll feel the unit pop up, then you can lift it out. It takes 2 AA batteries, thankfully not some bizarre disk batteries :)Btw when you look at the readout, you'll notice it's set in a silver square- that square is the computer module that pops out.Hope this helps!
Not finding what you are looking for?