SYMA Toys industrial Syma S006 Alloy Shark Rc Helicopters - Answered Questions & Fixed issues

check if the servo that controls the pitch is working

the tail rotor keeps it from spinning thats its job

To adjust the pinion you need to remove the tail boom. Remove the screws on the link below both sides. Once the boom is removed you will be able to adjust the pinion.

Your should exchange the product at the store you bought it from for another one. the problem lies inside the syma. it must have been a defect that the company did not notice.

It is no use to buy a new charger if the problem is a short. Indications are that it is. When the batteries are in need of replacement and wont charge up, overheating of the charger will also occur.

You have to remove the top piece by loosening a small screw just below the grip set then you can pull the inner shaft out from the bottom. Kind regards, Julian rccontrolfreak.co.uk

They generally have to be the same make and sometimes same model as well. Kind regards, Julian rccontrolfreak.co.uk

wrong!!! if the bottom set of blades aren't turning its because the drive gear for that shaft is loose and is spinning on the shaft instead of spinning the shaft itself. try tightening the screws but make sure the screws are lined up with the holes in the shaft so they seat otherwise your going to strip the plastic gears threads. if that doesnt work then you will have to replace the gear and shaft. its a cheap part and readily available. only problem is youll have to take apart almost the entire heli to get the old one out n the new one in. the gear comes pre-mounted on the shaft. Buy 2 or 3 of them right away as you will have to replace it just about every time your heli tips over while the blades are turning. the screws only go into the shaft about a 16th of an inch and is easily stripped out

Hi,
The spinning of the whole helicopter is cause by the rotor at the rear.
Look and read the manual on how it could be adjusted. There is an adjustment on the main board, that controls the speed of the motor.
if it doesn't work, you have a defective motor at the rear or the little electronic ic servo on the board.
Hope that helps you out!
Thanks for using Fixya!

Hi,
You need to assign the remote to the copter, turn on copter then remote, push forward on throttle then back, light on remote will stop flashing and remain static, there we go ready to fly have fun great machine.....

Sounds like you are missing the central support rod or bar that connects the Babyweaver swinging crib to the stand, providing stability and support for the crib. This component is crucial for maintaining the structural integrity of the crib and ensuring safe usage. Here are some steps you can take to address the missing part: 1. Contact the Manufacturer: - Reach out to Babyweaver or the manufacturer of the swinging crib to inquire about obtaining a replacement central support rod. - Provide them with details about the missing part and the specific model of the swinging crib to ensure you receive the correct component. 2. Check for Spare Parts: - Check if the swinging crib came with a user manual or assembly instructions that may have information about spare parts or replacement components. - Look for any contact information provided for customer support or spare parts inquiries. 3. Online Search: - Conduct an online search using keywords such as "Babyweaver swinging crib central support rod" or "Babyweaver crib replacement parts" to see if you can find the specific part for purchase. - Explore baby product retailers, online marketplaces, and specialty stores that offer replacement parts for nursery furniture. 4. Local Retailers: - Visit local baby product stores or furniture stores that carry nursery items. - Bring the existing part (if you have one side of the support rod) to help them identify and match the missing component. 5. Custom Fabrication: - If you are unable to find a suitable replacement part, consider contacting a metal fabrication shop or a carpenter who may be able to custom-make a central support rod that fits your Babyweaver swinging crib. - Provide them with measurements and details about the required specifications for the part.

It sounds like the drop may have caused some internal damage to the electronics or wiring of the Teddy Ruxpin toy. Here are some steps you can take to try and troubleshoot the issue:

1. Restart the Toy: Sometimes a simple restart can resolve minor issues. Try turning off the toy completely, including any power switches or buttons, and then turning it back on again after a few moments.
2. Check Battery Compartment: Ensure that the batteries are properly inserted and making good contact with the terminals inside the battery compartment. If the drop caused any displacement of the batteries, it might affect the toy's functionality.
3. Inspect for Physical Damage: Carefully examine the exterior of the toy for any signs of physical damage, such as cracks, dents, or loose parts. If there's visible damage, it may indicate internal damage as well.
4. Test with Different Devices: If the Teddy Ruxpin toy connects to a separate app or device for sound playback, try connecting it to a different device to see if the issue persists. This can help determine if the problem lies with the toy or the connected device.
5. Contact Customer Support: If none of the above steps resolve the issue, it's possible that the drop caused internal damage to the toy's electronics or wiring. In this case, you may need to contact the manufacturer's customer support for assistance. They may be able to provide further troubleshooting steps or offer a repair or replacement option.

Keep in mind that since the toy is relatively new, it may still be under warranty, which could cover repairs or replacements for damage caused by accidents like drops. Be sure to check the warranty information or contact the manufacturer for guidance on warranty coverage.

I was able to find you this website with all kinds of great craft kits for pre-kindergarteners.

This game is a great one to play with kids on a wet afternoon stuck indoors. Basically use their toys to turn an area of the house into a toy store. Get the kids involved in choosing the games they would like to 'sell'. Write prices lists and stick them somewhere that the kids can see and reach ie Lego sets - $4, Dolls - $2

If you don't have any pretend money, you can make your own with the kids, then divide up the tasks and let them enjoy many hours of pretend shopping.

I would contact your service provider for the code.

Question edited for clarity and spelling of the maker, 'Spaulding'.

Manuals Page

Spalding.com https://www.spalding.com > customer-service > info > m... Systems Manual Finder. You will need your model number to locate the correct manual. Please follow the steps below or visit our interactive manual finder. ..

Check Batteries: Ensure that the batteries are properly inserted and have sufficient charge. Sometimes, a low battery can cause the toy to stop functioning. Switch On/Off: Confirm that the toy is switched on. Some toys have an on/off switch or button that might accidentally get turned off. Connections and Wires: Inspect the wires and connections inside the toy. Loose wires or faulty connections can lead to malfunction. Obstructions: Look for any obstructions or debris that might be preventing the T-Rex's movement. Clear any blockages. Reset: If there's a reset button, try pressing it. This can sometimes resolve minor issues. Contact Customer Support: If none of the above steps work, consider reaching out to Fisher-Price customer support as below. https://service.mattel.com/us/ContactUs.aspx

You use a USB charger lead to charge the battery in the helicopter. The controller takes 6 x AA batteries. https://rc-today.ru/UserFiles/Image/Instructions/-S929.pdf https://www.google.com/search?q=rfd001+helicopter+charging+lead ..

It is too old (1970s) for that data to be on the Internet. There is one for sale on eBay, buy it and carefully look inside. https://www.google.com/search?q=Need+Play+%27N+Learn+Computer+420 ..