20 Most Recent
Kenmore Elite 20972 - Page 9 Questions & Answers
Kenmore he2 plus washer will not stay on.
One of your parts was faulty on delivery. Due to the cost of control boards, I would always advice a service call so that you get the correct diagnosis and warranty on the part and the labour if it goes wrong. Unscrupulous dealers will sell parts from scrapped machines that haven't been tested. eBay is the worst culprit.
..
Does a Kenmore Stackable Init have a reset for the washing machine?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
Kenmore elite washing machine with E2f2 error code
The E2F2 error code on a Kenmore Elite washing machine typically indicates a problem with the communication between the control board and the motor control board. This could be caused by a faulty control board, a loose or damaged wire connection, or a problem with the motor control board.
Here are some steps you can take to troubleshoot the issue:
- Unplug the washing machine for a few minutes and then plug it back in to reset the control board.
- Check the wire connections between the control board and the motor control board. Make sure they are secure and free from damage.
- If the wire connections are okay, you may need to replace one or both of the control boards. You can find replacement parts online or through a local appliance repair shop.
- If you are not comfortable working with electrical components, it's best to contact a professional appliance repair technician to diagnose and fix the problem.
I hope this helps!
Washer will not fill with water
Did you check the gauze strainer in the water connector.
To test for voltage, use your multimeter. Turn the machine on and set a cycle, then carefully use the probes to check for voltage.
Kenmore front load washing machine?. What does the L3 code mean please?
Question edited for clarity.
LE, not L3?
LE code on Kenmore washer
An
LE error code is displayed when the
tub fails to spin. The error code indicates that the motor can't operate properly because
you've overloaded the washing machine, or a foreign object is stuck in the tub.
Nov 21, 2022
How can I get my spin cycle to run if my timer is broken
If the timer on your Kenmore washer is broken, there are a few things you can try to get the spin cycle to run:
- Manually advance the timer: If the timer is stuck or not moving, try manually advancing it to the spin cycle. To do this, locate the timer knob and turn it clockwise until it reaches the spin cycle. Once you have manually advanced the timer to the spin cycle, try running the washer to see if it will spin.
- Use a multimeter to test the timer: If the timer is completely broken and not advancing at all, you may need to test it with a multimeter. You can find a multimeter at most hardware or electronics stores. Follow the instructions for using the multimeter to test the timer. If the timer is faulty, you will need to replace it.
- Use a jumper wire: If the timer is not advancing or you are unable to replace it right away, you can try using a jumper wire to bypass the timer and run the spin cycle. To do this, unplug the washer and locate the wires that connect to the timer. Look for the wires that correspond to the spin cycle and connect them with a jumper wire. Once you have connected the wires, plug the washer back in and try running the spin cycle.
Note: It's important to exercise caution when working with electrical appliances. If you are unsure of what you're doing, it's best to seek the assistance of a professional or to contact the manufacturer for guidance.
I have a Kenmore he2 plus washer model 110.47531702 that will not start
t's possible that there is an issue with the door lock mechanism or the door lock sensor. The fact that the door locks but nothing else happens suggests that the washer is not detecting that the door is locked properly. Here are a few things you can try:
- Check the door lock mechanism: Make sure that the door lock mechanism is clean and free of any debris or obstructions. Try manually engaging and disengaging the door lock a few times to make sure that it is working properly.
- Check the door lock sensor: The door lock sensor is a small switch located near the door lock mechanism. Make sure that it is clean and properly aligned. You can try pressing it manually to see if it is working properly.
- Check the wiring: It's possible that there is a problem with the wiring between the door lock mechanism, the door lock sensor, and the control board. Check the wiring harness for any signs of damage or corrosion.
- Check the control board: If everything else checks out, there may be an issue with the control board. Make sure that it is properly installed and connected. You may also want to try resetting the control board by unplugging the washer for a few minutes and then plugging it back in.
If none of these steps resolve the issue, it may be best to contact a professional appliance repair service for further diagnosis and repair.
Dripping in tub when complete
If your Kenmore washer series 400 model 22102 is dripping water in the tub after the cycle is complete, there could be a few potential causes. Here are some things to check:
- Water valve: The dripping could be due to a faulty water inlet valve. This valve controls the flow of water into the machine and if it's not closing properly, water can continue to drip into the tub even when the cycle is complete. You may need to replace the water inlet valve to fix the issue.
- Water level sensor: Another potential cause of dripping could be a malfunctioning water level sensor. This sensor tells the washer when the tub is full and it's time to stop filling with water. If the sensor is faulty, it may not be accurately detecting the water level, which could lead to dripping. You may need to replace the water level sensor to fix the issue.
- Drain hose: If the washer is not properly draining, it could also lead to dripping after the cycle is complete. Check the drain hose for any kinks or clogs that could be preventing water from draining properly. You may need to clean out the drain hose or replace it if it's damaged.
- Overloading: If you're overloading the washer with too much laundry, it could be causing water to overflow and drip into the tub after the cycle is complete. Make sure you're following the manufacturer's guidelines for load size to avoid overloading the machine.
If you're unsure of how to diagnose or fix the issue, it may be best to consult a professional technician or reach out to the manufacturer for assistance.
Not finding what you are looking for?