Top 20
Kenmore 44921 Front Load Washer - Page 5 Questions & Answers
Kenmore elite washing machine with E2f2 error code
The E2F2 error code on a Kenmore Elite washing machine typically indicates a problem with the communication between the control board and the motor control board. This could be caused by a faulty control board, a loose or damaged wire connection, or a problem with the motor control board.
Here are some steps you can take to troubleshoot the issue:
- Unplug the washing machine for a few minutes and then plug it back in to reset the control board.
- Check the wire connections between the control board and the motor control board. Make sure they are secure and free from damage.
- If the wire connections are okay, you may need to replace one or both of the control boards. You can find replacement parts online or through a local appliance repair shop.
- If you are not comfortable working with electrical components, it's best to contact a professional appliance repair technician to diagnose and fix the problem.
I hope this helps!
I have an E24 message on my Kenmore dishwasher - model 630.1390
The E24 error code on a Kenmore dishwasher model 630.1390 typically indicates a problem with the drain pump or the drain hose. This can cause the dishwasher to start adding water but then shut off and display the E24 error message.
Here are some steps you can try to fix the issue:
- Check the drain hose for any clogs or blockages. Make sure the hose is not kinked or bent and that it is properly connected to the garbage disposal or drain.
- Inspect the drain pump for any debris or foreign objects. Clean out the pump, if necessary.
- Check the air gap on the dishwasher. Make sure it is not clogged or blocked.
- Inspect the control board and check for any error messages.
- Power off the dishwasher and unplug it for 10 minutes to reset the electronic control board.
- Make sure the dishwasher is level and that the legs are adjusted properly.
If the problem persists even after trying these steps, it might be best to contact a professional technician for further diagnosis and repair.
Dripping in tub when complete
If your Kenmore washer series 400 model 22102 is dripping water in the tub after the cycle is complete, there could be a few potential causes. Here are some things to check:
- Water valve: The dripping could be due to a faulty water inlet valve. This valve controls the flow of water into the machine and if it's not closing properly, water can continue to drip into the tub even when the cycle is complete. You may need to replace the water inlet valve to fix the issue.
- Water level sensor: Another potential cause of dripping could be a malfunctioning water level sensor. This sensor tells the washer when the tub is full and it's time to stop filling with water. If the sensor is faulty, it may not be accurately detecting the water level, which could lead to dripping. You may need to replace the water level sensor to fix the issue.
- Drain hose: If the washer is not properly draining, it could also lead to dripping after the cycle is complete. Check the drain hose for any kinks or clogs that could be preventing water from draining properly. You may need to clean out the drain hose or replace it if it's damaged.
- Overloading: If you're overloading the washer with too much laundry, it could be causing water to overflow and drip into the tub after the cycle is complete. Make sure you're following the manufacturer's guidelines for load size to avoid overloading the machine.
If you're unsure of how to diagnose or fix the issue, it may be best to consult a professional technician or reach out to the manufacturer for assistance.
I have a Kenmore Elite front loader model 42198900 , this morning shut the door ,light stayed on and no power to controls, any ideas
If you have a Kenmore Elite front loader model 42198900 and the door light stays on while the machine has no power to the controls, there are a few potential causes you can investigate:
1. Check the power supply: Make sure the washing machine is properly plugged into an electrical outlet and that the outlet is functioning properly. If the outlet is not working, check the circuit breaker or fuse box to see if a circuit has tripped or blown.
2. Inspect the door lock: The door lock mechanism may be malfunctioning, preventing the machine from turning on. Check to see if the door is closing properly and if the lock is engaging properly. If the lock is faulty, it may need to be replaced.
3. Check the control board: The control board is responsible for sending power to the various components of the washing machine. If the control board is malfunctioning, it can cause issues like a door light staying on but no power to the controls. Check the control board for any signs of damage or wear, and consider having it tested or replaced if necessary.
4. Look for other potential issues: If the above steps do not identify the problem, there may be other issues with the machine that are causing the problem. Consider contacting a professional appliance repair service for further diagnosis and repair.
I have a Kenmore he2 plus washer model 110.47531702 that will not start
t's possible that there is an issue with the door lock mechanism or the door lock sensor. The fact that the door locks but nothing else happens suggests that the washer is not detecting that the door is locked properly. Here are a few things you can try:
- Check the door lock mechanism: Make sure that the door lock mechanism is clean and free of any debris or obstructions. Try manually engaging and disengaging the door lock a few times to make sure that it is working properly.
- Check the door lock sensor: The door lock sensor is a small switch located near the door lock mechanism. Make sure that it is clean and properly aligned. You can try pressing it manually to see if it is working properly.
- Check the wiring: It's possible that there is a problem with the wiring between the door lock mechanism, the door lock sensor, and the control board. Check the wiring harness for any signs of damage or corrosion.
- Check the control board: If everything else checks out, there may be an issue with the control board. Make sure that it is properly installed and connected. You may also want to try resetting the control board by unplugging the washer for a few minutes and then plugging it back in.
If none of these steps resolve the issue, it may be best to contact a professional appliance repair service for further diagnosis and repair.
Kenmore stackable washer/drier. Water doesn't drain out.
Kenmore stackable washer dryer doesn't cycle (doesn't advance to water fill or wash, drain, rinse, spin) (not spinning, draining, filling?) After the video, we learned it was the points in the timer. It wasn't the black "electrical plug", being plugged into. Get your serial number and google Kenmore timer and you can order a replacement timer. Even if you still have someone come out, you've still saved a bunch!.......ps....I had a viewer make a good point!; I obviously didn't have any issues, but obviously be careful with electrical panel and any loose wires!
I have a Kenmore model 110.25132411 in the rinse cycle only water takes a long time to fill. Then it just drains and doesn't spin.
If your Kenmore washing machine is having trouble filling and then drains without spinning during the rinse cycle, there could be a few possible causes.
- Water supply issue: The first thing to check is the water supply. Make sure the water supply valves are fully open and there are no kinks or blockages in the hoses. Also, check the water pressure and make sure it meets the manufacturer's requirements.
- Faulty water inlet valve: The water inlet valve is responsible for controlling the water flow into the washing machine. If the valve is faulty, it may not be allowing enough water to enter the machine, which can cause the filling to take a long time. It could also be stuck in the drain position, causing the machine to drain instead of filling. You may need to replace the water inlet valve.
- Clogged filter screens: If the filter screens in the water inlet valve are clogged with debris or hard water deposits, it can restrict water flow and cause the machine to fill slowly or not at all. Try cleaning the filter screens to see if this improves the water flow.
- Faulty pressure switch: The pressure switch monitors the water level in the washing machine and tells the control board when to start and stop the filling and draining cycles. If the pressure switch is faulty, it may not be sending the correct signals to the control board, which can cause issues with the filling and draining cycles.
If you have checked the water supply and filter screens and they appear to be working correctly, it may be necessary to replace the water inlet valve or pressure switch. If you are not comfortable performing these repairs yourself, it may be best to contact a qualified appliance repair technician to diagnose and fix the problem.
I am looking for a drive belt (?) for my Kenmore top-loading washing machine, Model 110.4563291.
You can obtain a drive belt for your Kenmore top-loading washing machine, Model 110.4563291, from several sources:
- Sears Parts Direct: They offer parts for Kenmore products and can help you find the correct drive belt for your model.
- Local appliance repair shops: They may have the drive belt in stock or can order it for you.
- Online retailers: Such as Amazon or eBay, offer a wide variety of washing machine parts including drive belts.
It's important to note the model number and the type of drive belt you need to ensure you get the correct part.
My Kenmore 500 will fill with water but after it fills the water won't shut off.
If your Kenmore 500 washing machine is filling with water but the water won't shut off, it could be caused by a few different issues. Here are a few things to check:
- Water inlet valve: The water inlet valve is responsible for controlling the flow of water into the washing machine. If the valve is faulty or stuck open, it may cause the water to continue flowing even after the machine is full.
- Water level switch: The water level switch is responsible for detecting the level of water in the machine and shutting off the water when the machine is full. If the switch is faulty or not functioning properly, it may cause the water to continue flowing.
- Wiring issue: There may be a problem with the wiring or the electrical system that is causing the water inlet valve or the water level switch to malfunction.
To determine the cause of the problem, it is recommended to bring your washing machine to a professional appliance repair service for further diagnosis and repair. They will be able to test the water inlet valve, water level switch, and other components to identify the source of the issue and recommend the appropriate repairs.
Not finding what you are looking for?