Top 20
Kenmore 44921 Front Load Washer - Page 4 Questions & Answers
Why does the water in a Kenmore washer 800 series top load washer as soon as you plug it into the wall it comes on starts running water and when the water cycle starts it doesn't stop running water
I would check with meter the water pressure switch and or the water inlet valve.
Washer fills with water and overflows:
The water pressure level switch is a pressure activated switch that is used to determine the correct water level in the tub. This part is normally located behind the control panel and will have a hose or air dome tube that connects it to the tub. On washers that use an electronic control, this switch may be located at the sump area below the tub. As the water fills in the tub it will compress the air in the tube and push against a diaphragm inside the switch. The switch will control the water inlet valve and turn the valve off at the correct water level. If the tube has a leak, not enough pressure may be created to activate the switch and the washer may overfill. If the switch is defective it may also cause the machine to overfill. To determine if the switch is bad, you should first eliminate the air dome hose as a problem. Look for signs of cracks or worn areas on the hose. Remove the hose and submerge in water. Seal one end and blow air into the other end and look for bubbles. Check for an obstruction in the hose as well. If the air dome hose appears to be ok, then the water level switch may be defective.
You can test it with a meter and with a manual test? ( first locate it in the panel, it has a plastic clear tube hose going into it, remove that tube from its connection, now put another small tube or hose into the slot where it was and have the machine set to wash cycle with water in it. Blow into the other end of the tube.
If the machine starts to wash. the pressure switch is more than likely good
( No wash- then THE DIAPHRAGM IS BAD AND SWITCH HAS TO BE REPLACED).
Another test u can make with a multi meter is by testing the prongs individually.
# 15,16,17 (don't worry to much bout the numbers IF U GET THEM WRONG) place ur meter prongs on both out side prongs or connectors of the switch.
(where the wire plugs into) take note of wether it shows OHMS or infinity ( open or close circuit) ? Now place the meter on the left outside and the middle prong, take note agin what it shows. Now place meter prong on the right outside and the middle prong. Agin take note what reading u get. ( you should actually get a reading of infinity in 1 and a reading of continuity or ohms in the other 2? Now the tricky part. Agin place a small tube or hose into the switch and blow into it, using the meter do the same test agin on all prongs. But now keep the pressure on the switch when u blow into it, in other words use ur tongue on one end of tube to not allow air to escape. When u test it agin now one of the prongs that once read infinity should now show continuity or ohms, and 1 of the other prongs that read ohms should now read infinity or open.
The other item to check would be your water inlet valve. Check it for continuity with a multi meter it should show Ohms or a closed circuit. Also check for hard water and debris build up in the screens located on the inlet valve To test it when water is overflowing unplug the unit and see if it still overflows or continues to fill. If it stops when unplugged. Then it is not a water inlet problem but an electrical signal problem going to ur water inlet valve. Possibly from the panel or board. You can also do a live volt test to see if it is getting the full 120 current, but be sure to unplug unit before testing as this is a live test.
Also another trick to check the water valve, is to first cut the water off and remove the hoses off the back of the washer. Then one at a time point the hoses inside the washer tub and turn the water back on. If you don't have good water pressure, turn the water back off and remove the strainer that should be in one end of the hose. Inspect the strainer to see if it is stopped up, clean it and reinstall it. Now repeat this test. If you have good water pressure now, reinstall hose and your problem is fixed
By the way my advice is free cuz God is good!
Kenmore 80 series will spin when draining, but not agitate or spin during spin cycle.
Hello. I'm a little confused at the description of the problem. You indicated it, "will not agitate during wash cycle or spin during the spin cycle." But later in your description you indicated, "It will however, drain and spin after wash cycle and during the rinse cycle." I'm not sure if you description was an error but it sounds like you will need to replace the coupling which is part number 285753A.
Kenmore Top load washer 11022242510 Will not agitate or spin.
There could be several possible causes for your Kenmore top load washer not agitating or spinning. The actuator is one possibility, but it's not the only one. Here are some other potential causes to consider:
Lid switch: The lid switch is a safety feature that prevents the washer from agitating or spinning when the lid is open. If the switch is faulty, it may prevent the washer from agitating or spinning even when the lid is closed. You can test the switch by using a multimeter to check for continuity when the lid is closed.
Drive belt: The drive belt connects the motor to the transmission, which turns the agitator and drum. If the belt is broken or worn, the washer won't agitate or spin. Check the belt for signs of damage or wear, and replace it if necessary.
Motor coupler: The motor coupler connects the motor to the transmission. If the coupler is broken or worn, the washer won't agitate or spin. You can check the coupler by removing the motor and transmission and inspecting the coupler for damage.
Transmission: If the transmission is faulty, it may prevent the washer from agitating or spinning. This is a more serious issue that may require a professional repair.
Based on the symptoms you described, the issue could be with the actuator, but it's hard to say for sure without further testing. The actuator controls the shifting of the transmission from agitate to spin, so if it's not working properly, it could prevent the washer from agitating or spinning. You can test the actuator using a multimeter to check for continuity.
If you're not comfortable diagnosing or repairing your washer yourself, it's best to contact a professional appliance repair service to diagnose and fix the issue.
Does a Kenmore Stackable Init have a reset for the washing machine?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
Kenmore he2 plus washer will not stay on.
One of your parts was faulty on delivery. Due to the cost of control boards, I would always advice a service call so that you get the correct diagnosis and warranty on the part and the labour if it goes wrong. Unscrupulous dealers will sell parts from scrapped machines that haven't been tested. eBay is the worst culprit.
..
How to clean Kenmore Elite sm 9711174 washing machine
To clean your Kenmore Elite SM 9711174 washing machine, you can follow these steps:
1. Clean the exterior of the machine: Wipe down the exterior of the washing machine with a damp cloth and mild detergent. Be sure to dry it thoroughly to prevent any water damage.
2. Clean the drum: Mix a solution of 1/4 cup of baking soda and 1/4 cup of water and pour it into the detergent dispenser. Run the machine on the hottest and longest cycle with an extra rinse. This will help to remove any built-up detergent residue or mildew from the drum.
3. Clean the detergent dispenser: Remove the detergent dispenser and soak it in warm, soapy water for 10-15 minutes. Use a soft-bristled brush to scrub away any buildup or debris, and rinse it thoroughly before replacing it.
4. Clean the lint filter: The lint filter is located near the bottom of the machine. Remove it and rinse it under running water to remove any lint or debris. If the filter is particularly dirty, soak it in warm, soapy water for a few minutes before rinsing it.
5. Run a cleaning cycle: Some washing machines have a self-cleaning cycle that you can use to help remove any buildup or mildew. Check the user manual for instructions on how to run a cleaning cycle on your specific machine.
By following these steps, you should be able to clean your Kenmore Elite SM 9711174 washing machine and keep it running smoothly.
Washer will not fill with water
Did you check the gauze strainer in the water connector.
To test for voltage, use your multimeter. Turn the machine on and set a cycle, then carefully use the probes to check for voltage.
Kenmore front load washing machine?. What does the L3 code mean please?
Question edited for clarity.
LE, not L3?
LE code on Kenmore washer
An
LE error code is displayed when the
tub fails to spin. The error code indicates that the motor can't operate properly because
you've overloaded the washing machine, or a foreign object is stuck in the tub.
Nov 21, 2022
Not finding what you are looking for?