20 Most Recent GE Profile PSW26P Stainless Steel Side by Side Refrigerator - Page 8 Questions & Answers

This is a link to a photo breakdown of the back of your refrigerator=> HERE Location 800 in that photo is the WR57X10070 Water Inlet Valve The problem you are having is possibly the=> WR57X10070 Dual Water Control Valve is not opening completely. I am adding a video so watch the video and I believe it will make this easier to understand what is happening. I am here should you have questions Thanks Sea Breeze

I have the same problem.
You will likely need a new one.
You can verify this as follows.
Remove the Ice catcher (using the lever on the right side).
There is a white Philips new the lower left front of the hollow area.
This screw holds down a long plastic cover.
After the screw is removed the cover can slide 1/2 inch towards the doors, then it can be removed.
Notice the little white hooks on the back that slide onto tabs (for when you replace this).
Reach to the back left of the hollow area - there is a cable that goes to the ice maker.
Free this cable.
On the top of the ice maker there is a little tab.
Press this tab and the ice maker can be slid forward 1/2 inch, then it can be lowered.
On the right side of the ice maker you will see a depression with a square depression in it, with a Philips screw in the center. This is where the Ice Full guide goes. You will likely notice it has broken off.

There are no serviceable parts on that ice maker and it will need to be replaced if you find it to irritating. Here is the part to order.

All parts come with a 365 day, any part, any reason return policy.

Unplug refrigerator and remove a rear panel on back side of refrigerator. Look for lose connection, signs of heat or burn marks on each side of your motherboard. WR49X10152 Main Control BoardHere is a link to a service manual HERE Electrical test can be found HERE I will be here to answer your questions, Sea Breeze

Check the condition of the teflon on the ice maker.  You will probably need to replace the ice maker if the teflon is cracking and getting into your ice.  

I'm not sure if this is a serious post but the cup drive sits in the ge ice maker cube holder tray and is at the back of the ice holder attached in a type of press fit fashion at the end of the 1 piece cork screw that moves ice from the tray to the dispenser............

Replacement parts can be purchased at any of the following web sites: searspartsdirect.com pcappliancerepair.com appliancepartspros.com repairclinic.com

partsselect.com

--------------------

Before going to buy any parts directly. Go through this troubleshooting help links. -------------------------

This is list of refrigerator problems, which is normally faced in refrigerator. You can go through the details, by clicking the link below:---

-------------- Refrigerator is not cooling properly? http://technoanswers.blogspot.com/2011/06/refrigerator-is-not-cooling-properly.html ----------- Both refrigerator and freezer not cooling properly in refrigerator? http://technoanswers.blogspot.com/2011/06/both-refrigerator-and-freezer-not.html ---------- The ice maker not working: --- http://technoanswers.blogspot.com/2011/06/ice-maker-stopped-working.html

------------ Compressor not running on refrigerator? http://technoanswers.blogspot.com/2011/10/compressor-not-running-on-refrigerator.html -------- Water dispenser not working on refrigerator? http://technoanswers.blogspot.com/2011/10/water-dispenser-not-working-on_19.html

-------------

Ice maker stopped making ice?

http://alltypesofpartsreplacing.blogspot.com/2011/10/ice-maker-stopped-making-ice.html

-------------

Water Overflows in Ice maker and freezes inside?

http://alltypesofpartsreplacing.blogspot.com/2011/10/water-overflows-in-ice-maker-and.html

-------------

How to replace Ice maker assembly?

http://alltypesofpartsreplacing.blogspot.com/2011/10/how-to-replace-ice-maker-assembly.html

These will help.

Thanks,.

I have a GE Profile Stainless Steel side by side. I also noticed that the refrigerator side door was not sealing like it had previously. There was no "suction" when opening. I started inspecting the gasket around the door to see if this needed replaced, as I had read that may be the problem from this forum. My particular model has the grill / vent at the bottom of the door, in the front, which just pops off. I found that down by the grill my model has magnets there that match up with magnets on the bottom of the doors. I inspected this and found a foreign object had attached itself to this magnet. I removed this object and waaahlaaah the door now has suction! I was relieved to find that I didn't need to replace the gasket. Worth a try. Hope this helps.

The freezer temp should be between 0 and 5 degrees and the refrigerator section from 34 - 37 degrees.