Evenflo Exersaucer Triple Fun Active Learning Center - Answered Questions & Fixed issues

my friend took it apart for me!

Here's an article on how to convert the Evenflo Exersaucer to the stage 3 activity table: How to Convert the Evenflo Exersaucer into Stage 3

Unfortunately, folding it to store is not a simple task. You'll have to remove the base which will allow you to fold the legs. Although the article I'm referring you to is for converting the exersaucer into a stage 3 activity table, it does give instructions on how to remove the base which will allow the legs to fold. How to Convert the Evenflo Exersaucer into Stage 3

Here's a detailed article that explains how to disconnect the legs from the exersaucer to convert it into the stage 3 activity table. It has photos and videos. How to Convert the Evenflo Exersaucer into Stage 3

Here's an article explaining how to covert the Evenflo exersaucer into the stage 3 activity table. How to Convert the Evenflo Exersaucer into Stage 3

1. Remove toys and seat from the exersaucer.
2. Fold exersaucer, but do not let the tray lock to the base. With exersaucer flat on the floor, twist each leg assembly (B) fully clockwise until it stops. Fully depress one of the pedestal locking tabs (C) then push on the leg assembly (B); leg will partially fold. Repeat this for all four legs. After pressing the fourth pedestal locking tab (C), the Exersaucer will fold with the tray (D) rotating toward the base (E). Make sure all four tray locks. (F) are locked onto the base before trying to carry exersaucer.
3. Place your fingers beneath the legs (A) push upward to disconnect the leg assemblies from the pedestals (B). Repeat for all 4 leg assemblies.
4. After all four legs have been disconnected from the pedestals, remove tray assembly (C) from the base (D).
5. Turn tray (C) upside down and remove both end caps (E) from beneath.
6. Squeeze both locking tabs (F) on each side of the tray to disconnect and seperate the tray halves (C). 7. Connect tray halves (C) to form activity table.
7. Connect tray halves (C) to form activity table.
8. Rotate leg assemblies (A) fully clockwise until they lock into postition. Make sure all four legs lock (G) are locked properly into the uper leg pedestal (H). Also make sure all four leg locks (I) are sticking out past the edge of the tray.
9. Turn table over and install two end caps (E). Make sure both end caps lock into place. NOTE: one end cap installs from above and the other installs from below.
10. Install toys on activity table. If desired, adjust table to the appropriate height for your child. IMPORTANT: NEVER use stage 3 without end caps!

Here's a step-by-step article for converting the Evenflo Exersaucer. It has photos and videos. How to Convert the Evenflo Exersaucer into Stage 3

Here's an article that outlines the steps for converting the Evenflo Exersaucer to stage 3. It has photos and videos. Also, if you compare your end cap with the ones in the video, you'll see whether or not your end caps were replaced. How to Convert the Evenflo Exersaucer into Stage 3

Here's an article along with photos and video on converting the Evenflo Exersaucer to the activity table: How to Convert the Evenflo Exersaucer into Stage 3

Here's an article along with photos and videos on how to convert the Evenflo Exersaucer to stage 3: How to Convert the Evenflo Exersaucer into Stage 3

Here is a link to the manual: file:///C:/Users/erwooster/Downloads/25707060.pdf States batteries are not replaceable, which means that they are buried somewhere inside the main module. Proceed at your own risk.

three diferent videos based on the age of your child. http://www.evenflo.com/flashvideo/TripleFunJungle/TripleFunJungle.html

You can get the install video on the link below. Last one on page called Secure Step™ Top of Stairs Gate Video

http://www.evenflo.com/sme_homesafety.aspx?id=342

Or you can call Evenflo at 1-800-233-5921 to have them email you the instructions.

Good Luck

hi here are the instructions
https://plweb.evenflo.com/product_search.aspx?txSearchModelNo=6231883&txSearchDOM=1/1/2010

hi
here is a page link to instruction download
near to bottom of the page

https://plweb.evenflo.com/product_search.aspx?txSearchModelNo=6231883&txSearchDOM=1/1/2010

This is the link to request an Evenflo instruction manual and replacement parts: https://plweb.evenflo.com/replacement_parts.aspx

I found this 800 number on the bottom of mine...1-800-233-5921 hope this works for U

There are several models of exersaucers, but hopefully the seat attachments are similar. Here is a video from Evenflo showing how to assemble the product. This might help you.

http://www.evenflo.com/resource.aspx?id=467&rcid=19

http://www.evenflo.com/resource.aspx?id=467&rcid=19
This may not be the one you have but this site will advise you how to get model and manufacture date so that you can get exact instuctions.

dtr