McCulloch Md7d0010 - 18v Cordless Driver Drill - Answered Questions & Fixed issues
Where can i buy a battery for mcculloh drill md7d0010
The charger for my McCulloch 18V drill (Model 7488) has these specs: 18V AdaptorInput: 120VAC, 60 HzOutput: 18VDC, 400 mAModel: TEAD-48-180400UI hope this info helps you source a charger from other outlets.Fred
8/8/2013 12:15:58 AM •
McCulloch...
•
Answered
on Aug 08, 2013
•
261 views
I have a model 7450-7468 cordless drill. The
Try www.batteryplanet.com and www.batteries.com. If neither one of these has what you're looking for, google cordless drill batteries and chargers and pick from there.
Happy surfing!!
11/22/2010 4:53:22 PM •
McCulloch...
•
Answered
on Nov 22, 2010
•
242 views
Chuck has broken how much is a new one
Depending on the size and manufacturer of the chuck a replacement should be between $35 and $50. You can replace it yourself by following the instructions on the new chuck. It's not very difficult and you can probably get the replacement at most Big-Box hardware outlets.
3/7/2010 4:44:39 PM •
McCulloch...
•
Answered
on Mar 07, 2010
•
83 views
Charger not working
3 possible reasons:1. Usually the cable of the charger is cut inside (the wire inside the cable).Try to change just the cable.2. The battery is Dead so it cannot be charged. Change battery.3. Inside the charger, the fuse or transformer are dead. Change them one by one and test in the middle.Another brilliant solution is: Buy a cheap Charger that fits your voltage and change the plug so as to bit your tool.
Was given a drill as a gift about 3yrs ago, tryed
After 3 years you probably can't get any kind of warranty support but you may be able to repair the charger or buy a universal one. www.centurytool.net sells parts for battery chargers....if you know where the drill was purchased, like sears, you may be able to take it there and they can either send it in for repairs or point you in the right directions. Most cordless drill batteries will go bad if they are not charged regularly so you may have to replace them also. Good luck!
How to remove oven door Maytag mgr5775qds
To remove the oven door on a Maytag MGR5775QDS range, you can follow these general steps:
- Open the oven door completely to access the hinges.
- Locate the hinge locks on both sides of the door. These are usually small levers or clips.
- Use a flathead screwdriver or your fingers to flip the hinge locks toward the oven cavity, releasing them from their locked position.
- With the hinge locks released, close the oven door halfway.
- Lift the oven door up and off the hinges by pulling it toward you and lifting it away from the oven.
- Place the oven door on a flat surface, such as a table or countertop, to work on it or store it.
Remember to exercise caution when handling the oven door, as it may be heavy and awkward to maneuver. If you're unsure or uncomfortable with removing the oven door yourself, it's always a good idea to consult the appliance's manual or contact a professional for assistance.
2/17/2024 5:19:51 PM •
Drills
•
Answered
on Feb 17, 2024
•
26 views
How to remove the chuck for Black & Decker 4.5 Amp Drill.
Insert the short end of a 1/4" or larger hex Allen wrench into the chuck and tighten. Facing the tool strike the long end of the hex wrench sharply counter clockwise as it is a standard right hand thread. This will loosen the chuck so that it may be unscrewed by hand.
Oct 12, 2022
..
1/23/2024 6:34:51 AM •
Drills
•
Answered
on Jan 23, 2024
•
28 views
Not finding what you are looking for?