Top 20
Swisher 44-Inch 12.5 HP Trailcutter #RTB12544 - Page 6 Questions & Answers
Which wires to connect to a new solenoid on Dixon ztr 4516k?
The solenoid should have three posts. Two large contactor lugs and a smaller terminal for control (batt pos). The solenoid frame must be securely attached to the mower chassis as it is the control winding return path (batt neg).
The large gauge red wire from the positive battery post and 2 smaller red wires stack on to one contactor lug (post 1). The other large gauge red wire from the starter goes to the other contactor lug (post 2). The small yellow wire goes to the smaller solenoid control terminal (center post) and energizes the relay with battery positive from the ignition switch S (start) terminal.
Refer to attachment, wiring diagram.
10/15/2023 11:02:44 PM •
Garden
•
36 views • 0 helpful votes
Living Accents Assembly guide for 8048106 pergola
1. Place the Pergola structure onto a flat surface in an area with adequate space for assembly and use.
2. Unwrap the hardware bag (included with the pergola) and place the contents on the flat surface near the structure.
3. Begin the assembly by attaching one of the long side rails to the top of the Pergola. Insert the rail into the slot at the top of the structure. Securing it with the provided hardware. Tighten the four screws using a drill to firmly secure the rail in place.
4. Next attach the second long side rail in the same fashion.
5. With both side rails firmly in place, attach the short side rails. Insert the rail into the slot at the top of the structure and then secure it with the provided hardware. Tighten the screws using a drill to firmly secure the rail in place.
6. Repeat this same process to attach the remaining short side rail.
7. Attach the four corner brackets using the provided lag bolts and washers. Some models may require different hardware for this step.
8. Secure the corner brackets with the provided bolts and washers.
9. Attach the remaining lag bolts into the holes in the top of the Pergola frame.
10. Tighten all the screws and bolts using a drill which will secure the frame in place.
11. Place the canopy (sold separately) on the top of the Pergola frame and secure it using the provided hardware and tools.
12. Once the canopy is secured in place.
10/31/2023 2:47:16 PM •
Garden
•
26 views • 0 helpful votes
BR 600 blower fuel line pops off
Leave fuel cap off and filter submerged. Ether fish out the fuel return or at least position where it's visible. Then press the purge bulb several times. Fuel should spurt out the return. If no fuel from return line and air bubbles come from filter, lines are reversed somewhere.
11/1/2023 2:09:39 PM •
Garden
•
24 views • 0 helpful votes
How do I tell what year model my Kabota RTV900 XT is?
https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwjF7pm4xpSCAxVEmIkEHaPbAvoQFnoECB0QAQ&url=https%3A%2F%2Fwww.orangetractortalks.com%2Fforums%2Fthreads%2Fcan-i-determine-what-model-year-from-serial-code.45724%2F&usg=AOvVaw320X8niJs2M0dRBU5lxjT6&opi=89978449
10/22/2023 5:13:23 PM •
Garden
•
28 views • 0 helpful votes
How to set idle speed on B & S push mower
On early model carburetor there is a throttle stop adjustment screw, newer models require mechanical adjustment.
Observe the throttle butterfly lever when adjusting the throttle.
10/22/2023 10:10:44 AM •
Garden
•
23 views • 0 helpful votes
What is the best wood material to build a storage shed?
Tanalized pressure treated cedar Joe. It looks nice, smells great and holds up well in the weather. If you don't stain it, the finish will go a soft grey, and if you want to bring it back, you can pressure wash it. Larch if you can get it, comes second. My waterwheel in England was cast iron, but the timber was Larch, and it lasted really well.
I hope you are doing well Joe and as it is Thanksgiving weekend in Canada, I will wish you a good one in advance!
..
10/7/2023 1:29:35 AM •
Garden
•
25 views • 1 helpful votes
Not finding what you are looking for?