John Deere 420,1020,2010,2020,2510,2520 Tractor Float - Answered Questions & Fixed issues


My Gehl CTL 80 runs for 45 minutes and star overhit i don’t wy

John Deere... | Answered on Nov 15, 2018 | 458 views


Try contacting John Deere. https://www.johndeeretechinfo.com/index.cfm/type/WIRING-DIAGRAMS/

John Deere... | Answered on Oct 26, 2018 | 349 views


Here's the link and I'm sure you will get the solution of your problem.

Manual for all you need
Heavy Equipment Service Manuals

John Deere... | Answered on Oct 20, 2018 | 1,850 views


You just go to the link I attached I'm sure you will get the solution of your problem -

Best Manuals

John Deere... | Answered on Sep 20, 2018 | 116 views


sounds like the wrong size belt or pulley

check routing of the belt also

John Deere... | Answered on Jan 29, 2018 | 116 views


is the primer working ? have you tried the self primer if fitted ? when you turn over the engine is the bubbles in the fuel viewer or does it just drop. or something else.

John Deere... | Answered on Jan 29, 2018 | 524 views


It is the pump and the pumps are about 1000 dollars. They are not that hard to install. IT should cost about 1500 total.

John Deere... | Answered on Jan 29, 2018 | 947 views


Have you checked the output of the alternator.
got a ohm/volt meter? or a battery tester?
should be putting out 14 volts. may be the voltage regulator.
start there esp if you charge the battery and it runs for a hour.... hour and 1/2 then quits.

John Deere... | Answered on Jan 13, 2018 | 84 views


Did you open the gas valve?

John Deere... | Answered on Dec 21, 2017 | 62 views


if the valves are working properly and good connections and battery, i would check to see if the compression release is working. i have one in the shop that the release came apart in the engine.

John Deere... | Answered on Nov 26, 2017 | 220 views


indicates that e retaining unit at the top bearing of the steering box has come loose and the shaft is moving up and down unrestrained by that top bearing

John Deere... | Answered on Oct 29, 2017 | 352 views


There are 2 safety switches on that unit as well. Most of them are right below the steering column in the firewall area. Search that to see if that unit has them. I'd be willing to bet one of them is faulty. Most are just a push button type.

John Deere... | Answered on Oct 21, 2017 | 132 views


Check battery voltage should be 12v or above. Battery could have gone bad or charging system bad. Voltage draw of electric clutch pulled battery down.

John Deere... | Answered on Sep 25, 2017 | 176 views


sounds like it is starter rebuild time

John Deere... | Answered on Sep 02, 2019 | 285 views


If not cranking replace the battery - they do wear out.

John Deere... | Answered on Aug 25, 2017 | 100 views


I had a similar problem and it turned out to be the automatic belt tension was blocked with grass so it was not tensioning the belt correctly. It was quite difficult to completely clean it but it has been fine ever since.

John Deere... | Answered on Jul 09, 2017 | 200 views


It sounds like your valves may need to be adjusted...
if they are too lose or worn they won't seat properly and when the engine fires it blows back through the intake valve.
pull the cover and see if the rockers are loose... it only takes one to give you a headache.

John Deere... | Answered on Jul 03, 2017 | 589 views

Not finding what you are looking for?
John Deere 420,1020,2010,2020,2510,2520 Tractor Float Logo

1,553 questions posted

Ask a Question

Usually answered in minutes!

Top John Deere Garden Experts

Joseph Mueller
Joseph Mueller

Level 2 Expert

346 Answers

john h

Level 3 Expert

22486 Answers

rjivaro

Level 2 Expert

158 Answers

Are you a John Deere Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...