I keep getting a E22 warning,I have removed the filter and checked the water but cannot find a problem
E22 is residual water in sump, this could be blocked pump, dirty filter, grease build up. If you have removed white pump cover to check for blockages, ensure that it is completely clipped back into position before trying again. The non return valve maybe allowing dirty water to drain back into the machine. If you tend to run a quick wash a lot, you may need to boil a kettle and pour it into the sump to clear any build up from around the optical sensor in the sump. Post if you need further assistance
Posted on Feb 23, 2013
We have a Bosch dishwasher.I cannot workout how to adjust the door spring tension.HELP
underneath are 2 L-brackets with the springs attached. Pull those out (with the door closed) and tension will be released. Shorten the strings attached to the springs and reinsert the L-brackets.
Posted on Dec 28, 2013
My Bosch dishwasher won't shut off. The timer says "1" forever and when you open it there is about an inch of SOAPY water still there.If you press start it goes to "13" and again counts down to "1" and stays there.
Bosch SHE44C06UC
The dishwasher continues to run...I followed instructions and performed the diagnostic...the light above the quick wash was solid, the light above the rinse/hold was flashing...the code displayed in the cycle countdown window was P0...now assuming the machins isn't "pissed-off"..can you help-
Posted on May 03, 2009
The dishes wash very well but when I take them out the glasses, bowls, and utensils still have water on them .I add Jetdry to the dispenser and it has very hot water.
My last dishwasher was a different brand and I had no problem. I'm very disappointed with this one.
this dw to save energy works this way- the final rinse will reach a temp of 161 F . the dishes have to absorb this heat. when the cycle is complete the dishes become a heater in themselves radiating the heat they absorbed during the final 161 F heat. If you have any tupperware or plastic dishes in the unit they will not absorb heat therefore not radiate the 161 f temp need to dry all the dishes. try to avoid plastic items and they must always have jet dry. this is the european way of conserving energy. on the old ge or whirlpool they had electric element in the bottom that would bake the dishes dry ....not these..but they do save alot of energy.. it helps right after a cycle to crack the door open release all the steam from the unit
Posted on Dec 21, 2008
The control panel on my dishwasher is showing a tap and E15
Mine's a bosch, same problem but started with E25 due to broken glass in the pump impeller, after struggling to remove it and then testing, it eventually moved to E15 as rightly so, no water was entering the machine due to the E25 code. The advice above is good, but take the device out first and tip the machine. This cured my faults without the need for a service call or spare parts.
Posted on Feb 11, 2013
Replace cover on Bosch Dish washer> Now a C6 code is displayed in the window
I had the same problem after replacing the white panel on my Bosch SHE45M02UC with a stainless panel. I got the C6 error code. I called Bosch customer service twice and neither rep was helpful. One guy told me he didn't know what the C6 code meant. He suggested that I call a local appliance repair guy and he would know what the code meant. I replied, you mean to tell me you work for the manufacturer of the dishwasher and don't know what the error code stands for but a local repair guy that doesn't work for Bosch does?
After all this frustration, I took the panels off and tested the dishwasher with no buttons. It worked fine! Turns out, each identical button isn't identical. Each one is labeled A-G. After putting it back together, no more C6 code! On a side note, try reseting the dishwasher. With the dishwasher on and door closed, hold down the cancel/reset buttons for 5 seconds and release. The disher should drain and reset.
Posted on May 11, 2011
My Bosche Exxcel dishwasher initially stopped mid cycle, full of water, I was told this was due to something hard stuck in brushes, - now removed offending article.
However now runs, if you open the door lets say at 31 minutes to go, it restarts at 34 minutes........then at end of cycle stays at one minute to go and does not altar from this. Has anyone got any ideas?
Make sure the drain pump is clear of any blockages and obstructions and that the drain hose wasn't kinked when you re-installed it.
Posted on Sep 04, 2017
how do I reset an old Bosch dishwasher SHI4302UC ?
Assuming that you can control power to the dishwasher from your kitchen panel switches, hold down the power on switch on the front panel of the dishwasher and recycle power (switch off and on) at the kitchen panel switch.
This will reset the dishwasher.
Posted on Sep 28, 2009
Model SHU43C02UC/17 consistently leaves film on glassware, leaves residue in the bottom of glasses in the back position of the top rack, and sometimes leaves gritty residue on dishes throughout the dishwasher. The stainless steel interior is also stained. I regularly clean the filter, use Jet Dry (the product that was included with the machine when I purchased it), and rinse the dishes before filling. The dishwasher has never cleaned dishes like the 17-year-old Kitchen Aid dishwasher that was in the house we lived in previously. We bought the Bosch to replace the cheap contractor's model that was in our condo when we bought. The Bosch was no improvement. Would I buy or recommend a Bosch? Never!!
Although I previously posted with the same problem of a film on the dishes after cleaning, I did find a section in the owner's manual which solved my problem. Lift up the rinse aid cap on the inside door - the factory setting is on "4". The rinse aid works in conjunction with your local water, which has variations in it's hardness or softness. When your dishes are streaky, lower the rinse aid setting to 1 or 2. If your dishes are spotted, raise the rinse aid setting higher.
Posted on Feb 20, 2009
SHE/43M bosch dishwasher fault code C3, P0, not washing, but draining
I have the exact same thing. While P0 is on the display, Regular Wash is lit and Quick Wash is flashing
Posted on Nov 14, 2011
1,005 questions posted
Usually answered in minutes!
243 Questions
226 Questions
184 Questions
155 Questions
156 Questions