20 Most Recent Bosch Classixx WVF 240S Front Load Washer / Dryer - Page 6 Questions & Answers

Gravel can't kill the motor. The motor is only connected via a drive belt. The only thing gravel can do is damage the pump as the gravel and water runs past the pump impeller! If it doesn't turn in wash (low speed), but it does spin in spin mode (high speed), my guess is the the belt needs tightening or replacing.

So basically it doesn't work at all. For a total failure like that it is likely to be the main control board, but because they are fairly expensive, you need proper diagnostics. Call for service.

Try doing a power reset. Disconnect power tonight before you go to bed. Some have a 'button press' reset procedure. Google Bosch (model) reset ..

https://all-errors.com/how-to-disassemble-the-bosch-washing-machine/

There are some videos in the link and if you click on the images tab there are schematics. The search query really needs the alpha numerical model designation though WRxxxxx. https://www.google.com/search?q=wiring+diagram,+bosch+classixx+series+4 ..

match old one at a hardware store

Likely a split hose, or a hose has come off. Pull the machine out and tilt it back against the wall. Have someone hold it whilst you check with a flashlight.

The blower motor is protected by the filters, so it shouldn't have an issue. The motor is hidden deep inside. Basically, you just undo every screw that you can find. Lay everything out in order and take pictures. https://www.google.com/search?q=Bosch+BGS4UGOLD2%2F11+vacuum+disassembly ..

E20 error code: Short or break causing incorrect resistance in winding of the circulation pump or the motor. D10 error code: Cause: Wiring/electrical fault related to motor triac. Action: Check wiring on/to PCB and motor. Check the triac (on the PCB). C01 error code: Cause: Motor tacho fault. Action: Check motor and motor tacho wiring for problems.

Slide a couple of sheet of newspaper under the machine and leave it a while and pull it out. The drips will show the approximate location. Then you can pull the machine out and lean it against the wall to check underneath. Make sure someone is steadying it. The most likely is a faulty water inlet solenoid valve.

I have never heard this before, but worth a try Resetting your washing machine

• First, you should perform a general reset of the machine. Turn the machine off at the power outlet, wait for one minute, and then turn it back on.
• If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved. If it drains, problem solved!

• Nothing in the manual
• https://media3.bosch-home.com/Documents/9001346934_B.pdf

https://www.hunker.com/13410561/how-to-reset-a-bosch-washer

possibly a bad control board .

Pull them

https://www.manualslib.com/manual/1916755/Bosch-Professional-Al-1820-Cv.html

On some Bosch models, E00 indicates that the machine is overloaded. Alternatively, the load is too heavy when wet. The machine can't safely spin the load. You may need to take this blanket to a laundry mat and use their commercial size washer. Try running the washer when empty. If the error recurs, then the problem isn't the blanket. Instead, the motor is working too hard to spin the tub. This could indicate a problem with the motor or the pulley and hub that connect the tub to the motor. I wish that I had better news for you. Cindy Wells

BAD CONTROL BOARD??

If your washing machine makes a loud rumbling or repetitive banging sound, which is particularly bad on a spin cycle, then it is most likely due to loose or worn out drum bearings.

Did you read the manual ?

https://iinjaz-alkhalj.com/

so order replacement or notify repair shop