Bosch Exxcel WFO 2264 Front Load Washer - Page 5 - Answered Questions & Fixed issues
I need to remove display on the newer Bosch HGR6767 toggle button type can't see screws under or side from front
On the newer Bosch HGR6767 ovens, the toggle buttons are usually held in place by clips or tabs rather than screws. To remove the display, you will need to carefully pry the toggle buttons off the control panel to access the screws underneath.
Here are the steps to remove the display on a Bosch HGR6767 oven:
- Turn off the power to the oven by switching off the circuit breaker or unplugging the oven.
- Locate the toggle buttons on the control panel. They are usually located above or below the display.
- Use a small flathead screwdriver or a similar tool to carefully pry off the toggle buttons from the control panel. Start from one end and work your way to the other end.
- Once all the toggle buttons are removed, you should be able to see the screws that are holding the display in place. Remove the screws using a screwdriver.
- Gently lift the display panel away from the control panel, being careful not to damage any wires or connectors.
- You should now have access to the internal components of the oven. If you need to remove any other parts, refer to the user manual or seek the assistance of a qualified technician.
- To reassemble the oven, simply reverse the steps above, making sure to connect all wires and components securely.
I have an bosch exxcel verio 7speed perfect washing that keeps showing the suds sign on every programm. ive cleen the pump, pipes and blownbut it keeps comimg up
The suds sign on your Bosch Exxcel Vario 7 Speed Perfect washing machine indicates that there is too much foam in the wash. This can be caused by using too much detergent or using the wrong type of detergent. Here are some steps you can take to try to resolve the issue:
- Reduce the amount of detergent: Check the detergent packaging for the recommended amount of detergent to use and reduce the amount if necessary. Overloading the machine with detergent can cause too much foam to be produced.
- Use the right detergent: Make sure you are using a detergent that is designed for use in front-loading washing machines. Using the wrong type of detergent can cause excess foaming.
- Run a rinse cycle: Run a rinse cycle without adding any detergent to help clear out any excess suds.
- Check the detergent dispenser: Make sure the detergent dispenser is clean and free from any residue or build-up that could cause excess suds.
If the problem persists, it is possible that there is a problem with the pressure switch or the control module of the machine. In this case, it is recommended to contact a qualified technician to diagnose and repair the issue.
Error code E:21on a Bosch Axxis front loader washer
Error code E:21 on a Bosch Axxis front loader washer indicates a draining problem. Here are some steps you can take to troubleshoot the issue:
- Check the drain hose for clogs or kinks. Straighten out any kinks and remove any clogs.
- Check the drain pump for obstructions. The pump is located at the bottom of the machine. Clear any obstructions from the pump.
- Check the filter for debris. The filter is located behind the front panel of the machine. Clean out any debris from the filter.
- Check the drain pump for proper functioning. Test the pump by running a cycle with an empty drum. If the pump is not functioning properly, it may need to be replaced.
If these steps do not solve the issue, it may be necessary to contact a professional repair service for further assistance.
Bosch sensixx b22l suddenly stopped heating iron and generating steam
If your Bosch Sensixx B22L iron suddenly stopped heating and generating steam, it is possible that the mainboard has failed or there is a security mode activated. Unfortunately, resetting the security mode or accessing diagnostics requires specific knowledge and tools.
If you have already checked the voltages and resistance of the valve, pump, iron heater, and steam heater, and they are all within normal range, it may be best to bring the iron to a qualified technician for further diagnosis and repair.
You can try contacting Bosch customer support or looking for a service manual for your specific model online. A service manual may contain information on troubleshooting steps, circuit diagrams, and resetting security modes.
Bosch WAT286H0GB washing machine. Tried replacing door hinge and cannot get front and back panels of door back together.
Replacing the door hinge on a Bosch WAT286H0GB washing machine can be a bit tricky. Here are some general steps that can help you put the front and back panels of the door back together:
- Make sure that all the parts are in the correct place and that the door hinge is properly aligned.
- Place the back panel of the door onto the front panel, lining up the hinge with the corresponding holes on the back panel.
- Insert the hinge pins into the holes on the back panel and ensure they are securely in place.
- Secure the panels together by tightening the screws.
- Check that the door is operating correctly and that there is no wobbling or loose feeling when you open and close it.
It is always important to refer to the manufacturer's manual for specific instructions on how to fix the door hinge on your Bosch WAT286H0GB washing machine. If you are still having trouble, it might be a good idea to seek the help of a professional repairman.
Bosch washing machine E24
https://www.bosch-home.com/us/experience-bosch/heart-of-the-home/tips-and-tricks/all-articles/e24-error-code
F8 washing machine me show kar raha hai kya kare
F8 is not a common error code for a washing machine, so it is likely specific to the brand and model of your washing machine. Without more information on the brand and model of the washing machine, it is difficult to provide a specific solution.
However, if you are seeing the F8 error code on your washing machine, the first thing you should do is consult the manual or check the manufacturer's website for the specific meaning of that error code. The manual or the manufacturer's website should provide troubleshooting steps specific to the error code.
If the problem persists, it's best to contact the manufacturer or a professional technician for help. They will be able to diagnose the problem and recommend the appropriate course of action.
It's important to note that F8 Error can be caused by various issues such as a faulty sensor, control module, door lock, or wiring, etc. It's best to get it checked by a professional technician
Bosch Serie 6 Exclusiv won't start washing, door light flashing even after door lock replacement.
Hi,
please verify with the product documentation that the flashing-door symbol indicates what you've initially mentioned. Apart from that, you might look for the sensor and hold it in to temporarily overcome the issue. If the door being shut is the issue, pressing in the sensor should fix the issue for you temporarily. If not, then you can work with Bosch or Home Deport to moving forward.
Prior to their arrival, you can power cycle your machine 1 or 2 times and check for the door symbol once more. It could be that they sensor has gone bad for some reason.
Thank you
Check water light on Bosch dishwasher
i think i would remove the outlet pipe take it to a yard water spicet and pressure blow it out to be sure it's clear then i would check where it connects on both ends to be sure those are clear then put it back together run it one cycle (empty) and see what happens.. it's also possible that the problem is from the screen in the water line going in.. being partially stopped up ... but i'm betting on the drain line.
Not finding what you are looking for?