20 Most Recent Delta RP17453SS Standard Diverter Tub Spout Brilliance Stainless - Page 3 Questions & Answers

Make sure the aeration unit is clean first

Take a coffee break and clear your mind about faucet. Remove # 7 and move rod # 2 to higher hole and reinstall #7. Also the is some adjustment using screw #2. This is an easy fix you can do it.

tapping it side to side helps.

Pull out the little red/blue plug, apply a thin coat of clear silicone sealant to the edges, and reinsert it. It'll stay in, but it can be removed in case of needed repairs.

Hi, W/D here.
Almost always, the shutoff valves are at the wall where water is supplied to the faucet. If the problem is with the drain piping, and the faucet valves don't leak, you don't have to shut off the water. Simply replace the drain piping and tighten it up. If you need any repair parts, you can get them from any hardware store. Please repost if there is anything else that I can help you with.
Good luck, and best regards,
--W/D--

first change the airator.

First, check your electrical connections from the battery pack to the faucet. If they are good, the next step would be to replace the batteries. Good luck!

There is a plastic horseshoe shaped retainer clip that must be pulled back from the housing to remove the hose. It can be a little tricky so bring a very small flat screwdriver with you to help pry the clip open.

Remove the handle by loosening the allen key. Next, unscrew the round retainer housing you just exposed by removing the handle. You now have access to the ball, cam, seats and springs for replacement.

-Bad seal. Replace the seal. Good luck Mai

The first thing to check is the filter screen inside the nozzle. There should be a ring that you can unscrew right where the water comes out. You will probably have to use a pair of pliers to loosen it. Use an old dishcloth or rag between the ring and pliers. This will protect your shiny faucet from being scratched! Once the ring is off, look inside it. There should be a metal screen inside with very fine mesh. It will come right out, but you may have to use the tip of a knife to pry up on one edge to get it started. Most likely, it is clogged with sediment. Clean it by holding the clogged side down under a running faucet. This is backflushing. Remove any remaining sediment with a fine brush and reinstall by reversing the directions above. Some people just never put them back in, preferring the stronger flow of water. Good luck!

Pump needs to be replaced.

Sometimes you have to get a little creative with your lift rod installs depending on your sink they can require a little more bending and customizing to get everything to line up. Just because the factory bent it a certain way doesn't mean you can't straighten it or bend it more

Please clarify your question.

There is a "p" trap in the drain. It can be cleaned by unscrewing it. You'll need to but a bucket under it to catch the water when you unscrew it.

Check installation manual if there is some indication about some kind of advice for this case. If there is no indication for the user, most probably your Delta Touch20 kitchen faucet is defective. Check your warranty terms about how you can return it to be changed or send it for service, so probably you'll have to uninstall it.

THERE HAS TO BE SOME THING HOLDING IT ON IT WILL NOT STAY BY ITSELF LOOK FOR A SMALL BOLT YOU CAN UNSCREW TO TAKE IT OFF. USE SOME WD 40 OR RUST REMOVLS SPRAY TO HELP LOOSEN.

THERE IS A BALL JOINT INSIDE THE FAUCET THAT YOU WILL NEED TO REPLACE YOU CAN GET A REPLACEMENT FOR IT AT LOWE'S OR HOME DEPO AROUND 5 BUCKS.

THE LINE MAY BE CRIPPED. TIGHTEN THE NUT OR REPLACE THE NUT IF IT WILL NOT TIGHTEN. YOU MAY NEED A LONGER WATER LINE TO GET AROUND THE BUMP.