20 Most Recent Cuisinart DFP-11 Deluxe Food Processor - Page 9 Questions & Answers

One of the major problems I have seen with food processors is the safety switch, which will not allow the motor to turn on if the bowl and top are not properly seated. The lever and/or switch sometimes wear to the point that they no longer work (easily). I'd do a bit more checking before I discarded the machine.

Remove the work bowl, blades, etc from off the base.
Plug the processor in and press the ON pedal down.
Use a pen to press in the rubber button on top of the base - you should hear a sound.
Now reassemble the bowl - lock the bowl in so that the handle faces front; insert blade of choice; place the tab under the feed tube of lid slightly left of center of the work bowl handle and slide the lid counter-clockwise until it clicks into place; insert pusher and make sure it locks into place.
You should be good to go again.

Work bowl handle should face the front of the processor, and feed tube/pusher should face the back of the processor. If it is still not working, call Cuisinart at 1-800-726-0190 as they are very hepful in helping you through the assembly.

In order for the processor to work, the bowl, lid AND pusher must all be in place - if one part is out of place, it will act dead. The proper assembly varies by model #. If you call Cuisinart at 1-800-726-0190, they are very good at getting you through the proper assembly.

Hi,

Your PowerBlend Duet™ comes with a food processor button. This button is the perfect speed for all your food processing tasks. Always use this speed when using the food processor. You may also use the Pulse button with this function for pulse-chopping.
To use your food processor, make sure that the bowl is assembled properly and the blade or slicing/shredding disc and the cover are locked into place.
When you use the control panel, the LED will light next to each button you press.
Press the On button. For continuous operation, press the Food Processor button. Motor will start if you have followed assembly instructions.
To turn motor off, press the Food Processor button again or the Off button.
For on/off operation, called pulse-chopping or pulsing, press the On button, press the Pulse button, and then press and release the
Food Processor button the desired number of times. Motor runs as long as you hold the Food Processor button down. The motor stops when you release control switch. Try it a few times.
You control the duration and frequency of pulses by the length of time you hold the Food Processor button down and the rate at which you press it. Pulses should be short bursts. Allow enough time between pulses to let food in work bowl fall to bottom.
Always use the Food Processor button for pulse/chopping. Never turn cover back and forth to start and stop processor.

You can download manual from the below link

http://www.cuisinart.com/share/pdf/manuals/bfp-10ch.pdf

ENJOY! RATE THIS SOLUTION
RNJ VINOD KUMAR

not sure what type you have. some have a tab/tang on the lid that when turned locks into side of processor. this is a safety switch. check lid for this. hope this helps. if not return for an exchange.

www.dealtime.com/xDN-kitchen_electrics_accessories-general_electric_griddle_parts -

The FPB-5SA is the Sam's Club version of the BFP-703. Here is a link to the manual:
http://www.cuisinart.com/share/man/10_man.pdf

-Tha Mp3 Doctor

There is no switch or relase - you just have to grip the sides and twist them off the base locks - requires quite a bit of force - not the easiest thing to remove.

Initial disclaimer: I am not recommending this course of action - my recommendation is to buy a new food processor. These units weren't designed for DIY repair, so this is going to be a difficult task. The final product probably isn't even going to be pretty. You are well out-of-warranty, or I wouldn't even consider posting this. First, make sure you have a DLC-7E shaft - the only way to get one at this point would be to buy a DLC-7E base from eBay or an after-market seller, as all of these were manufactured well over 20 years ago. I don't currently see any eBay listings for one, but they do crop up from time-to-time. Make sure the DLC-7E you are repairing and the old one from which you are wrenching the old shaft are unplugged and have been unplugged for an hour or longer just to be on the safe side. Unscrew the four screws on the bottom of the base on both units. If the bottom base does not come off after this, carefully pry out the four feet and unscrew any hidden screws that might be hidden underneath the feet (Careful - original feet cannot be ordered by normal means, and damage will only add to your total repair cost). Take note of the guts on the inside of both food processor bases - if you have to unscrew the motor body (4 screws that sit just underneath the top of the base), take note of everything that you are taking out so that you can put it back in its proper place when done. Wear leather gloves for safety. Please be aware that even an unplugged unit still has the potential to send several volts of electricity through your body - this is a potentially hazardous task. Once the motor body has been unscrewed and removed slightly (don't disconnect any wires or cables - just get the motor body out of your way), you will notice the old shaft that you intend on replacing. Look for any damage to the gears/bearing that surround this shaft. Try dabbing a small amount of USP-grade mineral oil on any bearings - clear away any dust or debris that may be obstructing the shaft from turning. Don't overapply the oil, or the wetness will seep into other electronic components in the motor and cause them to fail. Put your food processor back together, turn it on, and press the button/buttons on top of the base of the food processor with a pen with the food processor plugged in. If the shaft still won't turn, you definitely need to replace the old shaft (you can disregard some of these previous steps if your problem is that the spindle on the old shaft is worn).
Remove the screws and disassemble the processor base as described above. Since there is a layer of paint/coating surrounding the old motor shaft, removing the old shaft may cause paint flecking. Take the shaft from the one food processor base and insert it in the food processor you are trying to repair. Strip away any excess paint/coating from the new shaft. Make sure no paint flakes remain in the body of the food processor, or they will later cause more serious problems that will permanently damage your food processor - potential fire hazard as well. You will probably notice that the new shaft does not look as pretty as your original shaft, since the paint/coating will almost invariably get damaged in this process. Reassemble the base of the food processor, making sure no wires, etc. were knocked out of place in the process. This paint flecking will add to the cost of the repair - you may need to buy appliance body paint that dries to almost a rubbery consistency to make the final project look nice. All of the materials listed above could cost you $40 or more.

Like I said, I don't reccomend this course of action, but there's your answer.

Make sure the work bowl handle faces the front of the processor, the feed tube on the lid faces the back of the food processor, and the pusher sleeve lock faces the front of the food processor. Should then connect to the motor trigger.

You can get the manual here at this link.

http://www.cuisinart.com/manuals/index.php?item_id=53

Good Luck and Please Rate FixYa!

you must get help from the manufacturer of processor ready your owner manual and go to the website, and see the videos from them and fix it.God bless you

Amazon.com: Kenwood Mixing Bowl, Stainless Steel Bowl Chef Elite Food Processor Accessories Stainless Steel Bowl Titanium XL SS Bowl 6,7 Liter Silver: Home & Kitchen Amazon.com: Kenwood Mixing Bowl, Stainless Steel Bowl Chef Elite Food Processor Accessories Stainless Steel Bowl ELITE XL SS Bowl 6,7 Liter Silver: Home & Kitchen

Hello , you are search a slicing plate for your Kenwood food processor A530 maybe i will find that spare part for you , answer me on my email [email protected] i search for a bade cut for mine too

To order food on a train, you can use various online platforms like IRCTC e-catering, RailRestro, or local vendors available at specific stations. Simply provide your train details and select your preferred meal options through their websites or apps.

Question translated. We only speak English on this North American website. Question moved from Computers to Food Processors. No spares available for it. https://www.google.com/search?q=Silvercrest+SMZ400A1+parts https://www.manualslib.com/manual/2171818/Silvercrest-Smz400a1.html?page=30#manual ....