McCulloch MC1275 Steam Vacuum - Answered Questions & Fixed issues

You can find your parts on amazon. take a look here Amazon com Mcculloch MC 1275 parts. I hope this was helpful. cheers

see attached link http://index.about.com/index?am=broad&q=wagner+steamer+parts&an=msn_s&askid=2d930698-7f72-4fa0-81dd-13ced89fc4b6-0-ab_msb&dqi=wagner%2B905%2Bpower%2Bsteamer%2Bcleaner%2Bparts&qsrc=999&ad=semD&o=22874&l=sem

possible bad o-ring

Hi winnons2...

The only thing I could find on McCulloch is a phone number.
I am sure once you reach this number they would be able to help you farther.
To receive a user manual or parts.
You need to call 1-800-521-8559, ask for guidance to help with obtaining a USER manual and it will tell you where the parts go and what their name is and what you will use is for.
Ask for a PDF Manual, you will need the model number of the Steam Vacuum
They will email it to you for free
Please take time to rate me

check with sears they might help with brushes they sell these steamers

Here's a link to a site. Just downloaded one FREE

http://www.topinnovations.com/products/accessories/accessories.php

This is the best info I could find..

You can get the manual on link below. Scroll down to Product Details than click on the product manual.

http://www.amazon.com/McCulloch-MC-1275-Heavy-Duty-Steam-Cleaner/dp/B0000DF0RB

Good luck

Hi. Go to Steamfast's website. They sell accessories and pads for McCulloch steam cleaner. If you need further help, reach me via phone at https://www.6ya.com/expert/elixirjose_00375ea24bd8141b

It can cost a lot of money sometimes. But if it is really bad take it to a Vacuum Store they will fix it for you then they will tell you how much it is.

You can get the manual on link below. scrool down to Product Details than click on the product manual.

http://www.amazon.com/McCulloch-MC-1275-Heavy-Duty-Steam-Cleaner/dp/B0000DF0RB

Good luck and please rate

Were you able to find one of these? I need one also. thanks

Hello,

Here's a link to the instruction manual for the McCulloch MC1275 steam cleaner. If this helped you, please be so kind to leave feedback for me, or rate the repair. This is greatly appreciated, and is what keeps repair professionals answering free questions here on Fixya.

Thanks so much,

McCulloch MC1275 Steam Vacuum Owners Manual:

The 2.0 CID is Cubic Inch Displacement, the size of your motor. As for fuel mixture, generally a 50:1 is a benchmark for this. Typically, it should be 1 gal. of gas for 2.56 oz. of two stroke oil. They sell pre-packaged, pre-measured oil at your local DIY shop or lawn mower repair shop.

Its more than likely 50:1 mix.
Cheers
RICH

Storing a chain saw for longer than 30 days requires storage maintenance. Unless the storage instructions are followed, fuel remaining in the carburetor will evaporate, leaving gum-like deposits. This could lead to difficult starting and result in costly repairs. Never store a chain saw for longer than 30 days without performing the following procedures:
Remove the fuel tank cap slowly to release any pressure in tank. Carefullydrain the fuel tank.Start the engine and let it run until the unit stops to remove fuel from carburetor. Allow the engine to cool (approximately 5 minutes).
Using a spark plug wrench, remove the spark plug.
Pour 1 teaspoon of clean 2-cycle oil into the combustion chamber. Pull starter rope slowly several times to coat internal components. Replace spark plug.
Store the unit in a dry place and away from possible sources of ignition such as a furnace, gas hot water heater, gas dryer,etc. When removing the unit from storage, be sure to perform the following procedures:Remove spark plug. Pull starter rope briskly to clear excess oil from combustion chamber.Clean and gap spark plug or install a new spark plug with proper gap.Prepare unit for operation.Fill fuel tank with proper fuel/oil mixture.

This will help. Thanks, please keep updated. please do rate the solution positively .thank you for using fixya

Did you get the manual you needed? If not, e-mail me and I'll scan mine and e-mail it back to you.

tank filter goes to the primer bulb and then to the carb.

Found all the mcculloch manuals you could ever want on mcculloch product information site. Its run by mcculloch an you put the product weather chainsaw or strimmer whatever an the type in the next collum an press download then print it off all very easy. My manual was in german so made up i found stumbled on this.

The 3 adjustment screws are Idle, high and low.
First figure out which screws are which adjustment. Tighten the screws then turn them 1 full turn.
Then start the saw and get it warmed up. Work on the high adjustment. This does take a little while. after you get the saw running at high speed work on the low speed.