20 Most Recent KitchenAid KGST307 Gas Kitchen Range - Page 8 Questions & Answers

screws near the hinge, make sure to get oven/tempered glass sometimes the screws are located in the crack between the oven and door on the bottom

To replace the door glass do the following:

1 remove the oven door by pulling it up and removing from the the hinges. If glass is broken , then secure glass with tape. Have a table with a cloth on top ready to lay the door.
2 Remove the outer screws , starting from lower side of the panel.
3 Remove the inner screws. Keep all set of screws ordered, and take note of the order you remove them. You will follow reverse order in reassembly.
4 the frame will be free now,
5 Remove the external glass panel and leave it in a safe place.
6 Replace the inner glass.
7 Clean outer glass and metal door, re-assemble it and mount it back

See diagram below , click on picture to enlarge:

To replace the door glass do the following:

1 remove the oven door by pulling it up and removing from the the hinges. If glass is broken , then secure glass with tape. Have a table with a cloth on top ready to lay the door.
2 Remove the outer screws , starting from lower side of the panel.
3Remove the inner screws. Keep all set of screws ordered, and take noteof the order you remove them. You will follow reverse order inreassembly.
4 the frame will be free now,
5 Remove the external glass panel and leave it in a safe place.
6 Replace the inner glass.
7 Clean outer glass and metal door, re-assemble it and mount it back

See diagram below , click on picture to enlarge:



Here the part Inner Door Glass

To replace the door glass do the following:

1 remove the oven door by pulling it up and removing from the the hinges. If glass is broken , then secure glass with tape. Have a table with a cloth on top ready to lay the door.
2 Remove the outer screws , starting from lower side of the panel.
3 Remove the inner screws. Keep all set of screws ordered, and take note of the order you remove them. You will follow reverse order in reassembly.
4 the frame will be free now,
5 Remove the external glass panel and leave it in a safe place.
6 Replace the inner glass.
7 Clean outer glass and metal door, re-assemble it and mount it back

See diagram below , click on picture to enlarge:

You need to put door back in the hinges , pull it up and slide it back.

If door does not fit, you may need to have hinges replaced.

See diagram below , click on picture to enlarge:

is there power to the control touch screen circuit board? have u looked dor any blown fuses?

Your high limit thermal fuse has blown. Pull the range out and unplug it. Pull the back panel off and in the center of the oven you will find the thermal fuse. It will have 2 wires hooked to it on either side. This will be the problem child. If it is bad, it will show a broken circuit or no continuity. Replace this fuse if it reads bad (which it most likely will) and reinstall unit. Make sure to clean the vent in the front to insure that it is free from lint or insulation that would block or slow the airflow into the unit. This air keeps the unit from over heating during self clean.

Open your oven door and look at the hinges. You should see a drop down thumb lock on each hinge that you pull down and after you do so, lift up on the door as to close. The door will catch on these thumb locks and then at this point continue to lift up on the door as you pull the door out at the bottom. Reverse directions to reinstall.

Hello! Yes, I did figure out the beeping...while on a long hold with the kitchenaid helpline, I took the "cookie sheets off of the top of the stove" and voila the beeping stopped. Simple, but who knew? I hope this helps someone else.

the least expensive fix would be to buy an oven thermometer and note what setting is needed to attain 350 degrees and go from there. please rate me

unplug the oven for a few hrs, need a brand and/or model number to look up diag. codes

oven working but not heating past 50 degrees

I have a Kitchenaide Gas Range. KGST307 Inside glass on the oven door broke.. need to replace. is it easy to do? going to order glass online.. I did call some local repair people.. looking at a $200.00 to $250.00 bill to fix... NOWAY............ I can buy the glass and do it myself... Need some help if it can be done..... Any Help is COOL!! Thanks TED... 425-549-0150 WA. 98014

the gas leak can be the safety valve. in side the oven where the burner sits on you have to remove the burner to get to it.

all ovens, when they reach temperature they go off and on to kip the temperature, but if you smell gas the oven ignitor needs replacing, the ignitor gets red hot to ignite the burner ,but when ignitor does not get hot enough, it will have a delayed, that's the reason you smell gas.

As most electronic devices go you can just unplug it first for about a few mins then plug it back in.

sounds like the spark module is trying to light the elements. have a technician come out and take a look at it.

you do no tneed to remove the top to release the glass, yea aslong as the lower trim is removed then the only thing holding the glass, is the grease/sticky rubber gaket. lift up from the bottom slightly and twist out from the tabs. just be carefull when cleaning inner door glass, those "ridges in the paint, are just that paint, so dont use anything abrasive, youll ruin the finish!