KitchenAid KSB5 Professional Stainless Steel Work Top Blender - Page 4 - Answered Questions & Fixed issues

There is an air port near the adjustment knob. Open for a more blue flame and close for a yellow flame. If these haven't been moved before, you probably have a clogged jet at the burner. Just clean it out with a pin.

Would need your model number to look for a service manual, but first search did not show ANY service manuals online for a Kitchenaid blender. You can call the manufacturer at this number
Contact Kitchenaid Customer Experience Center at 1-800-422-1230. they may be able to help you find a local service center near you.

If you want to send us the model number of your blender we can look again for a service repair manual. Thank you for using Fixya.

poss.if taken apart and reassembled ,you did not reassemble properly causing something to catch,or your switch is dirty with debree,clean contact on switch. does the motor have a burnt smell to it if so then toss it and get another.

It's reversed threaded. tap in cw direction to remove. use a flat blade screwdriver and small hammer.

Hi, you have broken the coupler (sometimes called a coupling). It is relatively cheap and easy to replace. In the UK, K A Parts Limited sell them here and provide removal instructions here.

Hi, exactly the same thing happended to me. Apparently the repair shop can replace the rubbery bit for $20 (NZ)

Jules

well theres a couple of things you can do one is to soak the spring and ring in warm water with a dish cloth then take a butter knife and try to pry it up very carefully this usually works the other is to steam it free but that is very time consuming.

You will definitely need to change the clutch blade i.e. the black rubber rotating bit. Chaging it on the base unit may be difficult, I would check with your local Kitcheaid repairer for spare parts and repair advice.

Also check the clutch blade on the jug itself.

Hi,
There are several different control boards used in Kitchen Aid blenders. Call my store with your model # and I will give you price and availabity. 1 888 643 9806 9:00 - 5:30 Pacific time.

Mike

Direct or from eBay https://www.google.com/search?q=Kitchen+Aid+Model+KHB300+hand+held+blender+parts ..

Jimmy LavinderYou are tagging a dormant unanswered post that is 10 years old!The section up at the top is for you to ASK the Original Poster a QUESTION before giving him an ANSWER. You can't get any parts for anything online without an email address and a physical address. These parts are never found in a store. Durabrand is a cheap company of the 'sell and run' variety. There are no spares.https://www.google.com/search?q=durabrand+TSK-9368AP+partsDump it and buy a Vitamix, a company that guarantees spares forever or even a Braun, or Oster that guarantees them for 10 years...

Olabisi. It is better to create your own question rather than tagging a 13 year old question in the area where you ask the OP for further information before committing to an answer. Stir function runs the blades at a much slower speed to incorporate ingredients slowly. https://www.kitchenaid.com/pinch-of-help... STIR. To stir ingredients in a blender, start with a low, slow speed and gradually increase it to a medium speed. Blend until ingredients are completely combined. Different Blender Settings and What They Do - KitchenAid ..

Actually I do repair these stick types all of the time. The trick is getting the head off. Then its a simple Process to remove the shaft and clean inside and add bearings or bushings of needed. After removing the blade and blade holder, Remove the coupling at the top, then remove the 4 screws. After that you will see a aluminum washer. Stop here. To remove the head assembly, you need to make a large slide hammer like a split bearing. Lead or steel is good. Or a circle of cement 8 inches in Diameter and 4 inches thick. The inside hole should be as close to the diameter of the mixer shaft as possible. Cast it in two halves so when assembled it forms a ring around the shaft. Wrap this with lots of duct tape. also place a ring of duct tape around the plastic head where the cement will touch it. now wearing gloves, grab the metal base (or secure it to something with a chain or in the fork of a tree). Once secured, slide the weight quickly against the plastic head assembly. After a few hits the head should pop out. Then remove the shaft, replace the o-rungs in the center bearing, clean the unit & reassemble.Use Silicone as sealant when reassembling the body. There is no need to remove the lower seal assembly but clean it with a small bottle brush. I have included pictures of this procedure but im too ugly to make a You Tube Video. ;) These pictures are from my teaching tool and were cut to show anatomy. Theseafox Enterprises

Question edited for clarity. Question moved from Washing Machines category to Blenders. Something to do with the Outlet and Soy Milk! :>D https://www.amazon.com/gp/customer-reviews/R3S2NMMMKVYCV8?ASIN=B09L7PXN1B https://www.google.com/search?q=joyoung+a+super+power+blender+e08+error ..

Question edited for clarity. That is likely a failed heating element, failed thermostat, or worse case scenario, a failed control board. https://www.google.com/search?q=prolectrix+soup+maker+not+heating+up ..

the lock/unlock button on the Cuisinart Smart Stick CSB-75 blender may not stay locked when pressed in. The solution is to hold the blender in the palm of your dominant hand, press the low or high button and hold, then push and release the lock button on top with a finger on your other hand. The blender motor should start as soon as you push the lock button down and stay running until you release the high or low button. However, fix.com offers OEM Black and Decker blender parts and accessories, including rubber gaskets, jar bases, measuring cup lid inserts, and blade assemblies. You may want to check if the parts you need are available and replaceable. If you are unable to repair the blender yourself, you can contact Black and Decker customer service for assistance. They may be able to provide you with additional information on how to repair your blender or direct you to a local repair shop.

Send it back under the lifetime warranty on the motor. The motor is not working, right? https://www.google.com/search?q=bamix+blender+warranty ..

Question edited for clarity. It appears to be an eBay special. you may be able to buy using the diameter. Shops that sell fasteners sell O-rings, but this is likely wider, so more a gasket. https://www.google.com/search?q=GNC+Live+Well+Blender+BL3340+replacement+O-ring https://www.google.com/search?q=GNC+Live+Well+Blender+BL3340+replacement+gasket ..

"Elite Cosine" :>D I changed it for you and added '(what it is)'. Question moved from Elite Televisions. There may be a thermal fuse. But this is junk made in China. A complete new one will cost you $40 at BestBuy. If you can find a thermal fuse, you can replace it as a generic component by the details on it. https://www.google.com/search?q=Elite+Cosine+EPB1800+fuse ..

That sounds like it is overheating. Does the red power light flash before it powers itself off? Units like this with an enclosed motor often have an internal fan as part of the motor and vents on the base to drive out the heat. Various other ideas here and a link to Ninja Kitchen Support https://www.google.com/search?q=ninja+blender+starts+at+low+power+and+then+stops+when+increasing+the+power ..