20 Most Recent
KitchenAid KSM90 Ultra Power Series Stand Mixer - Page 7 Questions & Answers
My mixer is leaking oil. How do I fix it?
Your mixer is leaking grease not oil. It is a simple fix. First you have to open the machine and regrease it. Once you have done that
try replacing the gasket. Also, this particular mixer cannot be left on its side (some people store it sideways in a cabinet or under the sink) doing so will cause the machine to leak as well.
Leaking oil from drive/mixer head
There could be one of two things wrong (or both). You might need a new seal or you might just need the machine to be regressed. Also, never keep your mixer stored on its side as this will automatically allow the machine to leak grease.
When I turn the mixer on the lowest speed, it is
The speed on your KSM90 is controlled by three pieces: a Governor Assembly (35), a Control Plate Assembly (36), and a Phase Board Control (39/40 depending on the voltage of your machine). You just need to determine which one of those parts is bad and replace it. I have
attached a schematic to this post so you can easily see where these parts are located within the machine. Once you locate the bad part you can either bring it to an authorized repair center (or you can bring it to them to fix it before you open it up) or you can
purchase the items direct from us and we will be more than happy to send them to you.
Hi, the motor went slower
If you remove the meat grinder, does the mixer still work? It could be that the meat grinder is jammed.
You might have also blown a breaker. Have you tried plugging a lamp or something else into the outlet to make sure it's still working?
Ksm90 mixer won't unlock
Look for a reputable dealer that repairs KitchenAid mixers. It is worth the little extra money to keep it going well. I had a much needed repair 15 years ago...... it was 8 years old then, and it is still in great shape and working superbly!!
Mixer was turned upside down during move some oil
YES..... It's a KitchenAid... it's worth putting a little money into, and you want to guarantee that everything is in tip, top shape. I had mine fixed 15 years ago.... it was 8 years old then, it is still working great!! It is worth it and will last..... who knows? I'll probably pass this down to my daughter!
When I turn on my Kitchenaid mixer at any speed,
You need a reputable repairman. My gears were stripped after trying to mix a very thick dough. It would only work on high speed. After it was repaired.... I still use it, all the speeds work, and that has been 15 years ago. My mixer was at least 8 years old at the time of the "stripping".
When the mixer is turned
Sounds like a problem we had years ago. We put too much pressure on the motor by mixing a very thick dough for cookies. It stripped the "gears" and couldn't be used on slow.... it would instantly go to the fastest speed. We had to take it to a reputable appliance store that does repairs on KitchenAid products. I'm still using mine and that has been 15 years ago. It still works great!!
My Freezer stopped freezing and it is only 5 years
Hi,
As the weather is getting warmer for many people their freezer and/or refrigerator do not work right because of a dirty condenser coil...there are also many other things that can go wrong. If you are hearing a clicking or buzzing then check out the last two tips.
If your refrigerator is running but warm, then…
Check out this tip that I wrote about that... it is a great place to start trouble shooting your unit...and something that you can do rather then calling a repair person to do a simple thing for you...
Refrigerator Condenser Coil Cleaning Refrigerator Repair
Refrigerator Troubleshooting Refrigerator Compressor
Refrigerator Compressor Start Capacitor and Start Relay
heatman101
Kitchenaid mixer won't run changed out brushes and
The brushes need to be seated onto the armature. Try going from off to high quickly and tapping the motor housing. Once the motor starts, let it run for 15 min plus to seat the brushes. Keep clear of or remove beaters whille trying to get the moror running. In brief, the brushesaren't making good contact with armature. Good Luck
Mi batidora no prende
Hola EBANY780, veo tu pregunta es
acerca de su licuadora, pero le fue anunciado en la mezcladores KitchenAid. Mi
solución puede funcionar, pero posiblemente no.
Usted ha dicho, "Yo
pongo [en] mi pincel" - Supongo cepillo de la licuadora de motor eléctrico(s),
así que recomiendo que pruebe lo siguiente. Sólo hay una manera de volver a instalar los pinceles y
eso es lo que tanto el asiento correctamente en colector del inducido o no se
va a cualquier jugo "al motor. Véase la ilustración de abajo: Si te has vuelto un cepillo de 90 grados
demasiado, no encaja correctamente y tendrás el poder para el motor.
En esta ilustración se debe permitir volver a instalar los pinceles
con confianza. Buena suerte, espero que
esta ayuda. Howard, Burke, VA, EE.UU.
Si esta solución ha sido
útil, por favor, tasa que, gracias! - hslincoln
Please help
Hi,
I just took a look at my wife's... all you do is line up the pin and the slot in the attachment. Then push the attachment up over the pin and give it a twist... this will hold it on....just that easy!!
heatman101
Is there an exploded assembly diagram I can reference
Hi LONGLEY632. It sounds like you’re in the need of your
mixer’s parts list. It provides ‘reasonable’
exploded views of the various components of your mixer. Enough so that you can disassemble, identify
parts and reassemble your mixer.
You
can download a PDF version from the KA website at: http://www.kitchenaid.com/flash.cmd?/#/page/home.
Click
on Customer Care>Locate Manuals &
Guides> then enter the visitor type “Consumer” and the 6 character model number, in your case use KSM90P,
in the Model Number box. Select one the files
listed for your model that appears under Parts List (16): KSM90PSWH0.pdf (354.08 KB) and
save that file to your PC. Check to
verify this matches your mixer model.
Good
luck! I hope this helps. Howard, Burke, VA
If
this solution has been helpful to you, please rate it, thanks! -hslincoln
Not finding what you are looking for?