Top 20 Maax Brio II One-Piece Neo-Angle Corner Shower with MAAX IES 1/2 System - 1 Questions & Answers


You need the base taking out and installing properly.

If must be on a firm surface with no movement up, down, backwards or forwards. The best way is to glue it with a bed of expanded polystyrene so it can't move. Then you need a tile to shower edge filler which overlaps the base. Fill the gap with silicone, between the base and shower and when it is dry, put the edging piece on bedded into silicone. Then tile over the upper part of the edging.

Watch this video

Installing Shower Tray with Trimlux Shower Seal


shower tray edging Google Search

Maax Brio II... | 725 views | 0 helpful votes


www.maax.com

Maax Brio II... | 416 views | 0 helpful votes


Its probbably the hose connected to the valve, try screwing it back on and turn the water up slowly, if that does not help, check your local radio shack

Maax Brio II... | 2,612 views | 0 helpful votes


Hi,
Here it is...
Be patient it is a large pdf file...

http://www.maax.com/Upload/docs/premium/technical/en/000_10014442_0904-2_E.pdf

heatman101

Maax Brio II... | 3,128 views | 0 helpful votes


Request the manual from Maax.

Maax Plumbing | 487 views | 0 helpful votes


and what is your question --if you want to complain notify the company

Maax Plumbing | 82 views | 0 helpful votes


There are 2 types of litghly cover. A twist off (1/4) turn and a some pry off. It shouldn't be required hi torque. Try twist off first counter clockwise

Maax Plumbing | 438 views | 0 helpful votes


Generally the drains that are controlled from the
OVER-FLOW do indeed have a rod that goes down
from the face of the overflow... which lifts (opens)
the drain by lifting a hollow (typically plastic) sleeve
from in front of the outflow of the drain...

It is hollow to allow the OVERFLOW to work at all times.

The version you seem to have... WOULD have a
bellows like device that pushes on a plug lever...

More complex... but I seriously believe both may be
serviced through the OVERFLOW
(will attach a drawing below)...

OBVIOUSLY you will want to block the drain before rolling & dropping screws in, on & around the drain HOLE...

Once you see the diagram of the drain MECHANISM...
you will be able to see that jamming in a coat-hanger
was a terrible idea.

You can still most likely remove and repair the
mechanism ... (from the over-flow)

ELSE
You are looking at buying a new one and installing the entire drain from the bottom (hopefully).

Diagram of drains:
Go to Bing homepage

Carnac the Magnificent

Maax Plumbing | 868 views | 0 helpful votes


The drain may have been installed incorrectly. It should not be that easy to "pop" open. In normal operation, you push it down until it latches in the closed position. Afterwards, you push it down to unlatch it and start draining.

Maax Plumbing | 1,189 views | 1 helpful votes


Use structo-lite. Its easier to work with and much lighter. You want enough to make contact with the bottom of tub.

Maax Plumbing | 306 views | 0 helpful votes


look at the new frame to see how thick it is

Maax Plumbing | 314 views | 0 helpful votes


www.maax.com

Maax Plumbing | 290 views | 0 helpful votes


If it requires 110/220 volts and was wired to a double breaker... check to see that the do-it-yourself electrician put the breaker in a location that will give 220 volts and not 2 parallel feeds on the same side of the panel. Or else turn the double breaker off and then on to reset it.

Maax Plumbing | 48 views | 0 helpful votes


watch a few how to's on youtube

Plumbing | 33 views | 0 helpful votes


Might be your filter jamed so you can test with clean the filter. My website - Cleck Hare

Plumbing | 51 views | 0 helpful votes

Not finding what you are looking for?
Maax Brio II One-Piece Neo-Angle Corner Shower with MAAX IES 1/2 System - 1 Logo

10 questions posted

Ask a Question

Usually answered in minutes!

Top Maax Plumbing Experts

Jay Saari
Jay Saari

Level 1 Expert

18 Answers

john h

Level 3 Expert

22486 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Maax Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Maax Plumbing

  • Maax Plumbing

Most Popular Question

remove shower valve maax shower leaking

  • Plumbing
Loading...