1998 kawasaki ZZR 250 Logo

Related Topics:

Posted on May 16, 2009

1998zz250 lags when ur cruseing and then when u try give it sum gas it sounds like it wants to die4 a sec then gos normal i think its the carbs or the leads

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

  • Contributor 2 Answers
  • Posted on May 17, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Joined: May 17, 2009
Answers
2
Questions
0
Helped
133
Points
2

Check yuor rubber tube between carbs and cylinder head.maybe have some air leakage between it.also change your feul filter.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My cr 80 won't start but it's popping like it won't s to replaced spark plug an couple over things please help me sum one

Hi Lennard:
Cars and trucks section but CR80 sounds like a motorcycle. right?
You need two basic things:
1) Spark - pull the spark plug, connect the lead, hold against the head, and spin it over. Spark shoulld be hot and blue.
2) Fuel - Drain tank and fill with fresh gas
Drain and flush carb
If it has a filter, make sure that fuel is flowing through it.
Try a "normal" start........... choke, kick over 5 times. If no start, remove plug and check for fuel in cylinder. Wet plug means no spark. Dry plug means no fuel.
If dry plug try priming the carb (give it a squirt of gas with choke off)
It should try to start.
To let me know how you're doing, reply as a comment on this post.
Cheers.
0helpful
1answer

New carb on 49cc scooter. only runs for 30 secs then acts like it runs out of gas. still gas in new fuel filter that cam with carb

Sound like the float in the carb is getting stuck the way to tell is loosen the screw at the very bottom or carb and see how much gas comes out it should run forever if only runs for a few secs the clean out carb
0helpful
1answer

NO GAS IN CARBURATOR BUT GAS GOING THROUGH PUMP AND COMING OUT FUEL LINE

sounds like old gas, n carb can use cleanin put wire through were ur gas line gos on ull will have take carb apart wire should come out were jets r wen apart make sure clean carb good with old cloth n gas if looks clean ennuff try it out
Apr 09, 2011 • Polaris ATV
0helpful
1answer

Bike surges at cruseing speed,like it is losing gas,but at full throttle it pulls fine runs good.

It sounds as though the slow speed jets are partially stopped up. When you give it more throttle the high speed jets take over. Try using a good carb cleaner in it for a few tanks. If that doesn't work than you may have to go through the carbs.

Ride safely, Ed
0helpful
2answers

Snow blower won't start

just take off the AIR filter and thar is a Big Hole thar spray sum starte fluid in the bigger hole and spray it for three sec then try an start it
1helpful
1answer

A coleman generator 6875 won't start please give

Dump ALL old fuel out of tank, you might have got a clog in the fuel line, carburator, fuel valve. Remove carb bottom Sediment bowl then spray Carb cleaner thru the gas inlet AT the carb 3-4 secs CAUTION: KEEP YOUR HEAD BACK.. that cleaner hurts if you get it in your eyes... and NEVER SPRAY A HOT ENGINE (np with yours tho no start) Refill tank with NEW fuel (or strained at least if emergency remote repair) Place a suitable catch container over gas inlet line to carb (at carb) open fuel valve chk for fuel FLOWING (no dripping) into container. replace fuel line to carb start as normal
if not firing still chk that spark plug, might need cleaning now that rest is ok.
0helpful
1answer

2000 silverado 4.3 5 speed truck bucks at part throddle while driving.push down on the gas peddle and it gos away let up to just cruse and it surges and bucks again. replaced plugs,wires,cap,rotor.no...

sounds like it is in the throttle sensor or idle control valve causing problem not responding fast enough to take over also try the fuel filter could be clogged.
2helpful
2answers

Yamaha 2001 Raptor 660, need to clean my carb

Drain and replace the gas with fresh.
Remove the air cleaner and spray carb cleaner into the inlet. Work your throttle a little then put everything back together and try to start it.
Not finding what you are looking for?

90 views

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

Bob G

Level 2 Expert

104 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...