Top 20
1993 kawasaki ZZR 400 Questions & Answers
What are the factory settings for the carbs on a
Generally all carbs from the factory have a mixture screw setting of between 1 1/4 and 1 1/2 turn out from being bottomed out. Then I would check the sync on the carbs next. If that doesn't cure it then you can call a parts dept and ask them what the factory jets are and verify that you have those installed. Unless you have a pipe or full exhaust they should be factory. If you have aftermarket exhaust of slip on then you might have to dig a little deeper and see if it has factory parts or a jet kit. I’m happy to assist further over the phone at
https://www.6ya.com/expert/robert_5bac37c3cb991fdb
Bike just stoped
check wiring to egnition check spark plugs if not that dont no what else
No power and high fuel consumption
Suspect worn needle valve & seat assembly !---Quick test , with care>Whilst riding on open road &holding throttle at set position, switch off fuel supply & note IF engine speeds up, IMMEDIATELY Back off throttle, watch rear vision mirrors for traffic behind & switch on fuel supply!---If that small test indicates Carburettor area of further examination, UNLESS YOU ARE QUALIFIED the needle valves need to be examined byTrained eye!-(Especially wear on sides of needle valve & ALSO, check "floats"Stay Upright Des
Hey guys i need some help pls. on my zzr400k there
If you mean the bottom of the tank then one goes to the carb and one is just a breather/overflow that gets ran down out of the way and doesn't connect to anything. If you are talking about the carbs then one goes to tank and one goes to the vacuum
I have a zzr400 but with i start the bike i dont get any revs
Fuel system is clogged,..GARAUNTEED!! Take off the fuel tank,to get to the swirl bowl. Inside the swirl bowl,you will find a fuel filter,which SHOULD be completely white,and most likely,its not! Get a new filter and install it. While you have the tank off,disconnect the injector line,and remove and clean the injector with carb cleaner and pressured air.Put everything back together,and then add an INLINE FILTER to the feed line on the fuel pump which is located on the left hand side,running from the shut off valve,to the fuel pump. These are awesome quads,but the fuel injection system is a pain in the a$$.Good Luck!
Will a zzr 600 engine
Hello and welcome to Fixya, It can be done, one of our competitor's race teams did it with some pretty drastic modification's. Its definitely a challenge.But seen it accomplished. I could give you there info, they may be able to give you some hints. Let me know, Thanks for using Fixya
Dear Expert, As i have
Given the year of the bike there are a few things you will need to look over
*Check your break pads for even wear
*Change your break fluid
*Check your clutch lever (it should move about a millimeter before it actatually grabs the clutch)
*That bike has carborators. They need to be cleaned (could be part of problem 1 and 2)
*Check the fuel tank for rust. (there are treatment kits if it is rusted)
*your throttle cable should be lubed with cable lube(part of problem 1)/(when you pull the throttle cable then let go it should snap back closed)
*get higher octain fuel (this will help with problem 2)
Engine wont idle, fumes very,
They don't go too high on their own, someone has to have maladjusted them
It could be a leaking float, that will amount to the same fault. Or, it might be the choke is stuck on.
The bike starts and idles
- if u need more fast .. then don't change air filter and otherthings except oil...
- remove the BORE and give that to bore service centre they adjust it ,how much speed you want, only in bore don't go beyond that...
Not firing on number 3
You have two coils. Each operates two cylinders in what is called the wasted spark system. The plug fires on the compression and the exhaust stroke. If the spark plug is wet you have either a shorting wire , a bad spark plug cap , or a fouled spark plug. Try replacing the spark plug cap and spark plug.
If you still have spark on that cylinder and the plug is dry. You have a bad needle in the carburetor, a stuck float, or dirt causing the no fuel issue. You will have to clean and inspect the number three carburetor .
I have a 2002 Kawasaki Mean Streak 1500 I'm customizing it can the rectifier be moved so it's not just hanging there.
Absolutely, the rectifier on your Kawasaki Mean Streak 1500 can be repositioned during a customization project. The rectifier is a crucial part of the motorcycle's electrical system, converting alternating current (AC) from the stator into direct current (DC) to charge the battery and power the bike's electrical components.
While relocating the rectifier, it's important to consider a few key factors:
- Space and Mounting: Assess the available space on the motorcycle to find a suitable location for the rectifier. Ensure that the new position allows for proper mounting and secure attachment without interfering with other components or the bike's functionality.
- Heat Dissipation: The rectifier generates heat during operation, so it's essential to relocate it to an area with adequate airflow for cooling. Mounting it in a well-ventilated area helps prevent overheating issues.
- Wiring and Connections: When moving the rectifier, ensure that the wiring can be appropriately rerouted to reach its new location. Take care to maintain proper electrical connections and ensure a secure, stable wiring setup.
- Protection: Consider adding protective measures, such as shields or guards, to safeguard the relocated rectifier from road debris, water, or other potential hazards.
Modifying the placement of the rectifier may require custom brackets, mounts, or fabrication work to secure it in the desired location. It's crucial to execute the relocation carefully, maintaining proper electrical connections and ensuring the rectifier's safety and functionality.
If you're not confident in performing these modifications yourself, consulting a professional motorcycle mechanic or technician with experience in customizations can be highly beneficial. They can offer guidance, expertise, and ensure that the modifications are carried out safely and effectively.
12/15/2023 3:53:13 AM •
kawasaki...
•
688 views • 3 helpful votes
Not finding what you are looking for?