20 Most Recent 2001 KTM 640 Duke 2 Questions & Answers

TAKE IT APART REPLACE IGNITION

Check your stator and voltage regulator for proper output. Sounds like the battery isn't receiving a charge through the system. You can charge the battery with a trickle charger to verify the battery will take a charge outside the bikes charging system.

your relay is bad or the connections to it-

try to go for white brothers or FMF for 450cc up

177.0 km/h (110.0 mph)

your throttle cable is improperly routed and is being pulled on!

A worn wrist pin that attaches the piston to the piston's connecting rod

That would be like riding a fixed wheel bike.Think about how you will stop and start. Only hydraulic fluid will leak. Bad idea!

Question edited for clarity. That sounds like it is just a bad connection somewhere or possibly a bad switch. Remove the battery leads and clean the lead contacts and battery posts with a wire brush. Smear with Vaseline and reconnect. Remove the starter leads and do the same. Then it could be the Starter Relay https://www.google.com/search?q=ktm+450+sx-f+starter+relay+location Or Starter Button https://www.google.com/search?q=ktm+450+sx-f+starter+button+replacement ..

personnaly I would replace cylinder with new OEM

All dirt bikes have a VIN. It is on the steering neck. https://www.google.com/search?q=vin+on+my+ktm+300 ..

Have you checked battery connections. Run switch in the correct position? Checked spark plug for debris? Just thinking out loud..

Drain oil. Use degreaser to clean area. Use JB Weld & allow to set up properly before adding oil.

If you’ve found this helpful, please click the green “helpful” icon. If you have 20 seconds please leave a few words as a review or recommendation! Also, follow me for more answers to everyday issues, I’m all for saving you money and making the most of your time! Thanks and have a great day!

Hi, try to see this link and looking for the manual that you need. https://www.pdfmotomanual.com/manuales/ktm/eng I hope to give you an help. Luca

my ­b­est ­fr­i­e­n­d's s­ist­er-­i­n-­l­Aw ­m­A­k­es $74 ­ev­ery ­h­our ­o­n t­h­e ­c­o­m­put­er. S­h­e ­h­As ­b­e­e­n u­n­e­m­p­l­oy­e­d ­f­or t­e­n ­m­o­nt­hs ­but ­l­Ast ­m­o­nt­h ­h­er ­p­Ay­m­e­nt w­As $16505 just w­or­k­i­n­g ­o­n t­h­e ­c­o­m­put­er ­f­or ­A ­f­ew ­h­ours. ­g­o t­o t­h­is w­e­b s­it­e ­A­n­d r­e­A­d ­m­or­e ­g­o t­o t­h­is s­it­e ­h­o­m­e t­A­b ­f­or ­m­or­e ­d­et­A­i­l ... www.online-3.com

Hi, most likely your cdi unit or ignition coil needs replacing.

took me a min or two of WTF-ing to see pic and realize you meant a 2-stroke motorcycle..

try replace spark plugs

It's a bad seal of the head gasket. You need a new head gasket and to scrape every particle of debris from the cylinder head and cylinder surfaces that mate with the head gasket. Use the factory specified gasket sealing compound and do a clean job - no blobs or pools of the stuff. The head gasket should lay flat on the surface of the top of the cylinder, and you have to make this surface free of grit, leftover sealant and any other foreign matter before you put the head in place and torque it down. Start with the head bolts just finger tight and then go by the manufacturer's specs for the pattern and amount of torque to be applied. Usually it is recommended that you get to the specified torque amount in stages, going around several times and repeating the torque pattern until you get that maximum rated amount. This will prevent the seal from shifting or warping and should make the gasket seal perfectly. This is the old school method of doing this job. and I have never seen this fail to produce good results. Take your time, be clean, and you will have the results you want.

Check the clutch, adjust, clean, or replace