SOURCE: front brake pads
Just did this tonight... 7/21/08
You need a torx head T-55 Star Socket to remove the caliper bolt(s) and a large 3/4 in preferably with a 1/2 dr and large breaker bar or torque wrench with a 1/2 in dr. to remove the knuckle bolts. I should've taken pictures, but I did not. After studying this exact issue for an hour or so, I finally got everything to click. Steps as I proceeded. Loosen the top caliper nut using the T-55 torx bit, this will take some doing, if possible, use a breaker bar or something comparable, I used a standard 3/8 in. socket wrench and about a foot long hollow metal tube on the end as the breaker and after some muscle work (ouch!!) got it loose. Now there are 2 bolts that hold the caliper in place that need to come out. I used a 3/4 in socket on a 1/2 breaker bar to get these to break. I don't have the exact torque specs to put these back on, but I went about 40lbs on the knuckle bolts and closer to 80lbs on the caliper torx head screw. Once you have the caliper torx head bolt loose and the other 2 nuts off, you can rotate the caliper. Using a C-Clamp, compress the caliper so that it is completely compressed. Now, remove the torx head bolt and the pad assembly will swing out, at this point, you can remove the old pads and clips if you are replacing them as well. Reverse the order for installation using Lock-tite and the caliper grease you get from the parts store. I hope I don't have to mention removing the tires, using jack stands and being completely safe under there. Good Luck. The first side took me about 3 hours considering time and studying, the second side took about half an hour after already knowing what to do.. It gets easier each time you do it.
So far, I have replaced 2 fuel pumps (at home) first one took about 7 hours, second time around, only took about 2 hours. Front and Rear brake jobs. numerous small items, now I'm looking at a blinker switch (problem with left turn signal... rapid click, no light).. Also, the dash panel either needs repaired or replaced as the fuel gage is constantly up and down. If you or someone else has a suggestion here, I would appreciate it.
Thanks and remember... Practice Safe "Do it yourself"..!
SOURCE: replace front brake pad 2003 toyota 4 runner
Diagram is unnecessry.
Pull both front wheels
Work one at a time leaving the other for reference
Find the retention spring ... its a paperclip thickness wire spring... dislodge center retention loop and undo from both ends which engage brake pad retention rods.
Pull the rods out
Pull the old pads out... laying everything on the ground
Use scrap wooden wedges to pry between the rotor and the caliper ...inside and out until the calipers are fully withdrawn. Use the new pads to measure if they are far enough back.
Note... the brake fluid will have dropped in the master cylinder over many months of wear... do not fill it. When the calipers are pushed back they will fill the reservoir again... one wheel at a time.
Be sure to identify the correct pad based on what you took out and what is on the other side (if you screwed up the layout)
Make sure to take the old antisqueek backing plate from the old pad and place it on the new pad. They don't use lubricant on these anymore.
Replace the pads... the retention rods... then the retention spring
Do the other side
Then progressively step on the brake peddle until full tension is felt
Check the master cylinder reservoir... probably needs no additional fluid.
New pads will register in existing ridges in each disc in no time at all.
You should check the discs to see if they need to be replaced during this operation...using some calipers
SOURCE: 2006 dodge ram 2500 4x4 diesel replace brake pads front and back
Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.
SOURCE: what tool do i need to replace front brake pads on 2008 mariner?
You Will Need A 13-14 mm Wrench for Caliper Bolts .A Large Flathead Screwdriver to Spred open Caliper/Shoes to Remove Caliper from Rotor,
After rhis you Can use a LARGE "C" Clamp to CLOSE Caliper Piston.
24 views
Usually answered in minutes!
×