'96 Regal Purge Canister Valve?

purge Valve replacement........

https://www.youtube.com/watch?v=1TR9BoHhrJU

its all evap system codes. the evap system handles gas vapors from the tank. it wont affect the driveabilty of your car, just the ability to pass an emissions test.

PCV valve would have nothing to do with it !
P1443 - Very Small Or No Purge Flow Condition A fuel tank pressure change greater than a minus (-) 7 inches of H 2 O in 30 seconds has occurred with purge (fuel vapor) flow less than 0.02 pounds per minute.

• Blocked fuel vapor hose between EVAP canister purge valve and FTP sensor.
• Blocked fuel vapor hose between EVAP canister purge valve and engine intake manifold.
• Blocked vacuum hose between EVAP canister purge valve-solenoid and engine intake manifold.
• EVAP canister purge valve stuck closed (mechanically).

Check for blockages between the fuel tank, EVAP canister purge valve and engine intake manifold. Check obstructions in the EVAP canister purge valve diaphragm and ports.
Suggest you buy a repair manual if you want to try an fix yourself .Or Go to ford web site Ford Oem1stop com an pay 29 bucks for 72 hours for repair info . Or take it to a qualified repair shop an have it smoke tested . Or goolge purge valve for a pic. an see if you can find it under the hood .

Could be the P0445 - Evaporative Emission Control System Purge Control Valve Circuit Shorted
The EVAP canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the ECM. The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes
- Damage harness or connectors to the Purge Control Valve
- The valve circuit is open or shorted
- EVAP canister purge volume control solenoid valve may be faulty

When is the code detected?
- An excessively high voltage signal is sent to ECM through the valve

Try to remember this code number for additional details. Hope this helps, keep us updated.

code p 0441 refers to evaporative emission (EVAP) system --incorrect flow detected ==== causes --- hose connection/s--- intake leak---EVAP canister purge valve replace the purge valve

Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine

1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
2. Disconnect the vacuum pipe from the EVAP canister purge valve.
3. Disconnect the purge pipe from the EVAP canister purge valve.
4. Remove the EVAP canister purge valve and bracket.
5. Remove the EVAP canister purge valve from the purge bracket.
6. Inspect for carbon release in the EVAP canister purge valve ports.
   

To install:

1. Install the EVAP canister purge valve on to the purge bracket.
2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
3. Connect the purge pipe to the EVAP canister purge valve.
4. Connect the vacuum pipe to the EVAP canister purge valve.
5. Connect the EVAP canister purge valve harness connector.
6. Remove the air cleaner outlet resonator.
7. Disconnect the EVAP canister purge valve harness connector.
8. Disconnect the engine purge pipe from the EVAP canister purge valve.
9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
11. Remove the EVAP canister purge valve along with the mounting bracket.
12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines

1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
2. Remove the rear purge pipe from the EVAP canister purge valve.
   NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
   
3. Disconnect the EVAP canister purge valve electrical connector.
4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
6. Remove the bracket.
   

To install:

1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
3. Connect the EVAP canister purge valve electrical connector.
4. Connect the rear purge pipe to the EVAP canister purge valve.
5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines

1. Raise the vehicle
2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
3. Remove the hose from the EVAP canister vent valve.
4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
5. Remove the clip from the EVAP canister vent valve harness connector
6. Disconnect the EVAP canister vent valve harness connector.
   

To install:

1. Connect the EVAP canister vent valve harness connector
2. Install the clip into the EVAP canister vent valve harness connector.
3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
4. Lubricate the hose end with lubricant.
5. Install the hose to the EVAP canister vent valve.
6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
7. Lower the vehicle.

Hope this help (remember commetn and rated this).

The codes you are getting can be caused by one of the several parts to the canister purge valve. It would best be taken to a mechanic or you may be replacing parts that you don't need. Normally the evap canister purge valve has stuck or broken or disconnected.

maybe a fuse is blown? did you have the mechanic check the fuses? or even check all your relays and wiring?

The computer never tells you what to replce jsut the symptoms and whats malfunctioning, what is happening is it can't pressureize the fuel tank and canister purge valve, so i could be as simple as a bad gasket on the fuel tank or a dirty canister check valve or a broken hose on the purge canister so check these things first.

Look, that code means:
P0441 - Evap emission control system Incorrect purge flow

so try to replace the emission control.