I need to know how to get the hex nut out of my 1993 ford Ranger pickup-rear end ??

36mm is the consensus of opinion, but in reality, it is the socket that 'FITS'! Most socket sets come in metric and imperial, you use that one that is the best fit.

Axle nut socket ' Ford Explorer - Ford Ranger Forums ...

www.explorerforum.com > forums > threads > axle-nut...

Jan 22, 2008 - Anyone know what size socket for the axle nut? ... Mercury Mountaineer, Mazda Navajo, Ford Ranger, Mazda Pickups, and the ... 34mm front axle 36mm rear axle ... One more question, I know the bearing has to be pressed onto the hub but does it then ... Year, Model & Trim Level: 2004 Explorer Limited V8. Axle Nut Size? ' Ford Explorer - Ford Ranger Forums - Serious ...
Aug. 9, 2016
Front and Rear Axle Nut sizes? ' Ford Explorer - Ford Ranger ...
Feb. 28, 2016
What size socket is the wheel bearing nut? ' Ford Explorer ...
May 22, 2003
Spindle axle nut size ' Ford Explorer - Ford Ranger Forums ...
Aug. 19, 2009
More results from www.explorerforum.com

..

1993 Chevrolet Cheyenne K1500 4x4 truck Ralph, wheel nut size for your truck
Hex Size (mm): 22mm

• Thread Size: M14-1.50

• Hex Size (In): 13/16 Inch
• Thread Size: M14-1.50

• Hex Size (In): 7/8 Inch
• Thread Size: M14-1.50

List Wheel Lug Nut 1993 Chevrolet K1500 Pickup 4WD Reilly Auto Parts

There is a lug wrench in the rear acess panel that holds the jack and wrench. Depending on your van, either lift up on the cargo bin door in the rear and you will see a hex shaped nut or in the 2nd row seats there is a little circle that is cut out of the carpet with the same hex shaped nut. Use the lug wrench and turn the nut counterclockwise to lower the spare tire.

Hello there
FORD TRUCK
Wheel Nut Torque Specifications
Make/Model Description Years Torque Make/Model Description Years Torque
FORD (continued)
FORD TRUCK
E250 Van 8 Lug, 9/16" 2008-88 140 -160 ft lbs
E350 Van 8 Lug, 9/16" 2008-88 140 -160 ft lbs
Escape - 2003-01 98
Excursion - 2003-01 160
Excursion - 2000 148
Expedition - 2003-01 150
Expedition 19mm Hex 2000 100
Expedition 21mm Hex 2000 150
Expedition - 1999-97 100
F Super Duty Pickup 10 Lug, 9/16" 2003-99 165
F Super Duty Pickup 10 Lug, 9/16" 1998-96 140
F150 Pickup - 2003-01 150
F150 Pickup 19mm Hex 2000 100
F150 Pickup 21mm Hex 2000 150
F150 Pickup - 1999-88 100
F250, F350 Pickup 8 Lug, 9/16" 2003-01 160
F250, F350 Pickup 8 Lug, 9/16" 2000-99 148
F250, F350 Pickup 8 Lug, 9/16" 1998-88 140
Ranger, Windstar - 2003-87 100

For 1993 Ford Truck Ranger 4WD 3.0L MFI 6cyl the Control Module-Ignition is located under hood, center, rear engine area, mounted on distributor.



Fig. 1: View of the remote mounted Ignition Control Module (ICM)

Hope this help (remember comment and rated this).

There are some special 4 tooth and hex sockets for removing the nuts inside the hubs of the truck.
YOu can find these at NAPA or maybe AutoZone or Advance. I would go to NAPA because they more than likely have it and also know something about repairing this assembly.
Ford uses Dana front end parts and NAPA has original Dana parts in stock... so it is as good as or better than original and they would have the tool for it.
Be careful and follow the procedure exactly for putting the front hubs back together.
YOU CAN RUIN THE FRONT END OF THE TRUCK IF YOU DO NOT PERFORM THIS SERVICE CORRECTLY.
And trust me... many of the idiots working in repair garages do not know how to do these older 4x4 hubs either... ask someone and read the books for the right procedure... some of the older mechanics may show you how to do it. Ask

Should be adjustments at the ends of your emergency cables that run along your the bottom of your truck frame . at the ends around the differential . loosen the nut and give it a few turns equally on both sides if theres two adjustments.

sounds like ah sensor or somthin dont really know

the fuse box is inside the pickup under the drivers side dash, there is a flasher which is the round one in the fuse box, it controls turn signals and emergency flashers also in the same fuse box, there is a 15 amp fuse which controls just the turn signals it sits vertical instead of horizontal.