SOURCE: How to change the whole headlight assembly on a 05 Honda CRV
When you raise the hood, look for a Phillips screw that holds the parking lamp in. if it is there remove screw and pull parking lamp toward front of vehicle. If headlamp and side lamp are 1 piece, there should be 2 number 10 mm headed bolts that are vertical, that hold the assembly in. The side lamp will have a stud that holds the light to the fender. You may have to pry it loose. Reverse procedure to install.
SOURCE: removing rear light assembly on honda odyssey 2006
Yes, there is a "spear point" plastic clip that is still engaged into a socket type holder in the front outboard portion of the tail lamp assembly. Pry gently with a tape wrapped screwdriver at the front outboard corner of the assembly and the clip will release. You will then be able to see how the clip works and will be able to align and engage it first when replacing the tail lamp assembly.
-T
SOURCE: replace airbag on `92 honda accord
When an SRS cable reel assembly is removed and set aside during vehicle repairs, the cable reel may rotate inside the assembly so it is no longer centered. If the assembly is reinstalled with the reel off-center, the cable can break when the steering wheel is turned to full lock. The cable reel holding fixture locks the reel while the assembly is off the vehicle, keeping it centered for reinstallation.
CABLE REEL REMOVAL PROCEDURE
1.
Follow the procedure in the appropriate service manual for disconnecting the battery, and removing the dashboard panels, steering column covers, airbag, and steering wheel.
^
Always install short connectors on the connectors for the driver's and passenger's (if so equipped) airbags.
^
Make sure the front wheels are pointed straight ahead before removing the steering wheel.
2.
Verify that the cable reel is centered; the yellow gear tooth is lined up with the alignment mark on the cover. Install the cable reel holding fixture in the cable reel assembly as shown. Use a TORX T-10 wrench.
3.
Disconnect the 6-P connector, then remove the cable reel assembly.
CABLE REEL INSTALLATION PROCEDURE
1.
Verify that the front wheels are still pointed straight ahead.
2.
Reinstall the cable reel assembly, and reconnect the 6-P connector.
3.
Remove the cable reel holding fixture.
4.
Follow the service manual procedure for reinstallation of the steering wheel, airbag, steering column covers, and dashboard covers.
5.
Verify SRS operation as described in the service manual. Road test the vehicle.
^
If the steering wheel spoke angle is not correct, change it by adjusting the tie rod ends. Do not remove and reposition the steering wheel.
PARTS INFORMATION
Cable reel holding fixture:
For 1992-95 Civic and Ohio-produced 1992-95 Accord
P/N 77900-SPO-999, H/C 4733564
For 1991 Accord Wagon, 1992-95
Prelude, 1995 Odyssey and Japan-produced
1992-95 Accord
P/N 77900-SM5-999, H/C 4733572
WARRANTY CLAIM INFORMATION
Use the Flat Rate Manual information for the repair being performed.
SOURCE: 1999 Honda Civic "DRIVER" Side Headlight Bulb Replacement..
Okay, 1999 Honda Civic, Headlight (Driver Side). If you haven't fixed this or just wanna know, this is what you have to do. The power steering pump is in the way of you getting to the bulb. You will need to remove the back tube of the power steering reservoir, the one closest to the cabin of the car. Plug this tube with a rag, quickly as fluid starts flowing immediately. Pull the res up and out of the holder it sits in. Now on to the light. Grab a hold of the black plastic clip (with wires) on the sides, and pull the electronic clip out of the light. Gently pull the rubber tabs for the weather guards, and you should now see your old bulb. There is a metal clip that holds the bulb in place, gently release this metal clip, being careful to keep it in place. Makes the job easier when you put it together. Your old bulb can now be easily pulled out. I take the bulb at this point and plug it into the clip and test the lights. This assures me that the bulb is busted and a bigger job isn't ahead of me. Once confirmed, I place the new bulb in the headlight bezel, careful to not touch glass. Clip the metal hold down clip back in place. Put the Rubber grommet back in place, clip on the electrical wire clip. Test the headlight. Put power steering tubes back in place, place the res back on the holder, and done. The book and this site: http://www.andrewdothay.net/blog/2007/11/24/1998HondaCivicHeadlightReplacement.aspx helped me a lot!
211 views
Usually answered in minutes!
×