The great news is you can program your 2005 Honda Pilot Key Fob yourself. All you have to do is follow these instructions:
Most remotes can be self-programmed. If these procedures do not work, you must have your remote programmed by a professional automotive locksmith or dealership.
Procedure #1
Obtain all remote transmitters for this vehicle. Entering programming mode erases all remotes, so all remotes must be programmed during this procedure.
Procedure #2
Obtain all remote transmitters for this vehicle and read the instructions prior to programming.
Entering programming mode will erase all previously programmed remotes for this vehicle. You must have all remotes available for programming including working ones.
Perform each of the next three steps in order, then repeat all three steps two more times for a total of three times each.
Next, turn the ignition switch to ON position, marked II.
4. Using the same remote, press the LOCK button again. The door locks should cycle indicating the vehicle has ENTERED programming mode.
5. Using the same remote, press the LOCK button again. The door locks should cycle indicating the vehicle has PROGRAMMED that remote.
If you have other remotes to program then repeat step 5 with each additional remote one after another. Step 5 must be completed within ten seconds for each additional remote. You may program up to three remotes.
6. Turn the ignition to OFF. Test all remotes.
If your remote has a trunk button you will need to hold that button down for several seconds for that function to operate.
SOURCE: Code to program my key fob
Here are the program instructions
1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode
SOURCE: reprogram key fob
Here is a quick HowTo on programming your own keyless entry:
1) Turn ignition to OFF.
2) Locate the Data Link Connector, its a black 16 pin connecter that is under the driver's side dash, right where your right knee would be. You have to look up into the dash from below to see it.
3) Ground pin 1 of the Data Link Connector by taking a wire or paper clip and running it from pin 1 to pin 4. Pin 4 is ground so you can just short pin 1 to 4 and it will be grounded. Grounding pin 1 tells the system you are ready to reprogram it.
4) Close all of your doors.
5) Turn the key to ACC then back off. The power door locks will lock/unlock. This is the signal that the system is ready for reprogramming.
6) Push a button on your key fob, doesn't matter which button.
7) If you have 2 key fobs, then press a button on the 2nd fob within 1 minute of pressing a button on the 1st fob. Both must be programmed at the same time. If you only have 1 fob then press a button 2 more times to signal that you only have one.
8) The doors will lock/unlock to signal the codes were received.
9) Remove the jumper wire from the data connector.
10) your done
SOURCE: reprogram 2005 dodge durango key fob
Daimier Chrysler North American Remote Keyless Entry Programming procedures
Program Method A (Customer Program Method)
1. Press (LOCK) button 5 times at 2 second Intervals to resynchronize
transmitter, Attempt to function transmitter, If working as designed discontinue
programming.
2. Turn ignition to run position, (Allow Ignition chimes
to stop).
3. Using any original (working )transmitter, press the [UNLOCK]
button for 4 to 10 seconds.
4. Within the specified 4 to l0 seconds, continue pressing
the [UNLOCK] button and press the [PANIC] button for 1 second and release both
buttons (AN/DN release either button first). A chime will sound to indicate
that the transmitter programming mode has been entered (allow 3 seconds for
chime to sound).
5. Press [LOCK] and [UNLOCK] buttons simultaneously for
1 second and release (a short chime will sound for AN/DN).
6. Press and release any button an the same transmitter
and a chime will sound after successfully programming the transmitter (locks
will cycle for AN/DN).
NOTE.- (FOR DR ONLY) A CHIME WILL NOT SOUND ON STEP #6 FOR THE FIRST TRANSMITTER
PROGRAMMED, BUT WILL SOUND UPON PROGRAMMING THE SECOND TRANSMITTER.
7. Repeat steps 5 through 6 to program additional transmitters.
8. Turn ignition to OF:F position. Transmitter programming
mode will discontinue after 60 seconds (30 seconds for AN/DN and RS). (All transmitter
programming must be completed within time specified).
SOURCE: Resetting a Key fob on 2007 Honda Pilot
to program a key fob- get in vehicle and close all doors. insert key into ignition, have all the key fobs you want to program for this vehicle in hand, programing erases all old fobs. turn the ignition switch to on(all dash lights light up, on click before starting the car). then hit the lock button on one of the fobs. turn the ignition to lock. turn the ignition back to run and press the lock button again from the same remote. repeat untill all the locks cycle. ones the locks cycle keep the ignition in run and press the lock button on each key fob(the ocks will cycle each time a button is pressed). then turn the ignition to lock after all fobs have been programed
SOURCE: How do I reprogram the key fob on my 2005 Hyundai
Well, you basically have only 3 choices: TECHNICAL SERVICE BULLETIN Group
1. Pay the fee at the dealership
2. Purchase the high-dollar equipment that is required to perform the programming procedure
3. Forget about adding another key fob to tor vehicle.
90 - ELECTRICAL
Number
03-90-020
Date
October, 2003
Model
Elantra 2001-2004, Santa Fe 2001-2004, Sonata 2002-2004, Tiburon 2003-2004, XG(NNN) NNN-NNNNand XG(NNN) NNN-NNNN2004
Subject
SECURITY SYSTEM KEYLESS ADAPTER CABLE
This bulletin supersedes TSB # XXXXX
DESCRIPTION:
The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03 or newer) and Data Link Connector (DLC) Cable.
SERVICE INFORMATION:
The keyless adapter cable can be used on the following vehicles:
^ 2001 -2004 Elantra
^ 2001-2004 SantaFe
^ 2002 - 2004 Sonata
2,106 views
Usually answered in minutes!
×